ABB Thomas & Betts Elastimold 252LRJS-IEC Installation Instructions Manual

ABB Thomas & Betts Elastimold 252LRJS-IEC Installation Instructions Manual Manual pdf 1 page image

IS--1627IS--252LRJS--IECRevision: 0Page 1 of 5Installation Instructions: 252LRJS--IECDeadbreak Elbow Connectors with Jacket SealCONTENTS: Elbow Connector Housing, Compression Lug, Probe, Probe Wrench, Lubricant, Hold--down Bail,Installation Instructions.The 252LRJS is designed to terminate UD jacketed and non--jacketed cable having concentric neutral wires or copper tapeshielding. The elbow provides a voltage test point and an operating interface for connecting to an 12/20 (24)kV 250amperedeadbreak bushing or accessory device. Designed with a fold down extension on the cable entrance for sealing to the jacket ofjacketed cable. When other types of UD cable are to be terminated, an appropriate Elastimold cable shield or grounding devicemust be used.DANGERAll apparatus must be de--energized during installationor removal of part(s).Do not touch or move energized products in the workarea.These instructions do not attempt to provide for everypossible contingency.Failure to follow these instructions will result indamage to the product and serious or fatal injury.This product should be installed only by competentpersonnel trained in good safety practices involvinghigh voltage electrical equipment. These instructionsare not intended as a substitute for adequate training orexperience in such safety practices.All apparatus must be installed and operated inaccordance with individual user, local and nationalwork rules and electrical standards.For loadbreak products follow operating instructions.All deadbreak connectors must be de--energized beforeoperating. All 250A deadbreak connectors must bemechanically secured with bails when connected.If this product is supplied with a protective shippingcover(s), remove this shipping cover(s) and replacewith the appropriate HV insulated cap(s) orconnector(s) before submerging or energizing thecircuit.Inspect parts for damage, rating and compatibility withmating parts.Excess distortion of the assembled product may resultin its failure.FOR MORE INFORMATION ON PARTS, INSTALLATION RATINGS AND COMPATIBILITY, CALL THE NEAREST ELASTIMOLD OFFICE.Limited Warranty:1. T&B warrants that its products will be free from defects in materials or workmanship for a period of two (2) years, except for tools which are warrantedseparately (see warranty accompanying those products). Fisher Pierce products and Elastimold Reclosers are warranted for three years; and JoslynVBT and VBU capacitor switches are warranted for four years or 40,000 operations whichever occurs first. Upon prompt notification of a warranted defect,T&B will, at its option, repair or replace the defective product.2. In no event shall T&B be liable for any consequential, indirect or special damages, nor will T&B be liable for transportation, labor, or other charges arisingout of the removal or reinstallation of its products. Liability for breach of warranty is limited to the cost of repair or replacement of the warranted productonly.3. Misuse, misapplication or modification of T&B products immediately voids all warranties.THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES AND REMEDIES, INCLUDINGBUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WHICH ARE SPECIFICALLYDISCLAIMED.IMPORTANT1. Read entire installation instruction before starting.2. Check contents of package to ensure they are completeand undamaged.3 Check elbow housing cable entrance size andcompression lug size to ensure proper fit with cable.4. Check threads by threading probe into compression lug.If resistance is encountered prior to full assembly, checkfor damage and replace damaged component.5. Unit Must be Bailed.6. Have all required tools at hand and maintain cleanlinessthroughout the procedure.Compression LugProbeOperatingEyeASSEMBLED ELBOWElbow Housing Test PointIntergral CableJacket SealCaution: If test point cap is not installed, lubricate cap and test point and install cap.IS--1627IS--252LRJS--IECDate: December 2017Printed in U.S.A.8155 T&B Boulevard, Memphis, Tennessee 38125(800) 888--0211 Fax: (800) 888--0690