ABC Office 130 User Manual
 |
SPECIAL PURPOSE CUTTERUSERS GUIDE TO:INFORMATION, ASSEMBLY, OPERATION, MAINTENANCEPARTSModel #142 Model #136 Model #130Cutting Length: 42” Cutting Length: 36” Cutting Length: 30”THE QUALITY IS BUILT INDahle Cutters are recognized the world over as the finest in precisioncutting. These high quality cutters have been carefully engineered toprovide years of service with a minimum of maintenance. DahleCutters use only the highest quality Solingen Steel blades, ground andtempered to exacting standards. Each cutter has been carefullyassembled and tested to meet Dahle’s highest standards.For more information about Dahle products contact ABC Office at 1-800-658-8788.WARRANTYNOTE: Unless the Warranty Card is properly and promptlyfilled out and mailed, you will not be protected under thewarranty terms.Dahle USA warrants each new Cutter to be free from defects inmaterial and workmanship for a period of one year after the originalpurchase under normal use and service. Each machine will bethoroughly inspected by us before shipment to ensure perfectcondition. We agree to repair or replace any such defective unit orparts, at our discretion, provided the defective unit or parts arereturned to us intact, transportation prepaid, within the guaranteeperiod, and that our examination disclosed to our satisfaction that theunit is defective. This warranty shall not apply to any cutter or partthereof which has been repaired or altered in any way, so as, in ourjudgment, to affect their reliability or stability, nor which have beensubject to misuse, negligence, or accident.THIS WARRANTY is expressly in lieu of all other warrantiesexpressed or implied, and the manufacturer neither assumes orauthorize any representative or other person to assume for it, anyother liability in connection with sale, maintenance, or repair of saidcutter.NO CUTTER is to be returned to us for any reason without ourpermission and return merchandise authorization (RMA) number.DAHLE USA whose policy is one of continued product improvement,reserves the right to make changes in design aand the construction at anytime without incurring any obligation on cutters previously sold.ASSEMBLYWhen assembling or moving your Cutter, remember the BLADE ISSHARP. Keep the blade closed when handling or moving the Cutter.After positioning the Cutter, install the Guard before using the Cutter.THE BLADE GUARD IS FOR YOUR PROTECTION.INSTALLING GUARDThe Guard is installed with the blade closed. Place the guard betweenthe Blade and the Hold-down, small end to the rear of the Cutter. Thelarge end of the Guard should rest in the guide on the blade near thehandle. Install fully threaded screw through the Hold-down post at therear of the Cutter and tighten with the proper screw driver.Install the threaded pin through the front Hold-down post and againtighten with screw driver. The Cutter Blade should open and closewithout binding.HOLD DOWN SYSTEMThe material hold-down system should be used by applying andholding pressure while cutting.BLADE ADJUSTMENTThe Blade is pre-set and should stay in the open position withoutfailing. Should adjustment be necessary, the large chrome lock nutmay be tightened until the blade stays up. Do not over tighten.USING THE CUTTERProper operation of you Cutter is important to fine cuts and long life.This cutter is capable of cutting and trimming a variety of materialsfrom a few thousandths of an inch thick to over ¼ of an inch. Thetype and thickness of the material your Dahle will cut is determinedby the density or toughness of the material itself. We recommend toangle the blade slightly in the direction of the cutting edge in order toachieve a clean cut with even the finest paper. With properoperation, your Cutter will produce clean, straight cuts.ACCURACYThe Scales on your Cutter are carefully adjusted to be a true 90degrees to the blade. Careful positioning of work and use of thehold-down will ensure accurate cuts. |
Related manuals for ABC Office 130
manualsdatabase
Your AI-powered manual search engine