ACIS AD-300i Instruction Manual
FUNCTION SETTINGS1. Press [ON/OFF] to turn on the scale, the display will show flash digits andthen --------, press [PRINT], the display will show b xxx BAU value (press[UNIT] to select among 1200, 2400, 4800, 9600), our default setting is 9600.Press [ZERO] to enter Parity mode, the display will show P XXX PAR, press[UNIT] to select odd,even,none (odd stands for 7 data bits with odd parity, evenstands for 7 data bits with even parity, none stands for 8 data bit without parity)ourdefault setting is none.Press [ZERO] to enter Print mode, the display will show n xxx Mod, press [UNIT]to select ON, OFF, KEY, STB (OFF stands for serial data output disabled, KEYstands for demand mode by press [PRINT], STB stands for automatic print whenscale is stable, ON stands for continuous print, our default setting is STB. Press[ZERO] again to return to weighing mode.2. Press [ON/OFF] to turn on the scale, the display will show flash digits andthen ----------, press [UNIT] to enter unit selecting function, the display will showON X (X stands for the units: g, oz, lb, dwt…tola...) press [UNIT] to select ON(activate the selected unit) or OFF (inactivate the selected unit), press [ZERO] againto return to weighing mode.3. Switch the power to “ON” and than press [ON/OFF] to turn on the scale。Thedisplay shows F-E-9 to 0 and than “- - - - - - -”|,press [PCS] key to enter ZEROtrack function setting,display shows ZRD x.xd,press [UNIT] key to select ZEROtrack value(0.0d-0.5d-1.0d-1.5d-2.0d); press[ZERO]key to enter ZERO trackfunction setting,display shows ZRT x.xd,press [UNIT] key to select ZERO tracktime(05. to 4.0 seconds; press [ZERO] key to enter ZERO setting,display showsRZD XXX, press [UNIT] key to select ZERO value(0.8d-1.8d-2.8d-3.8d);press[ZERO] key to enter FIL setting, press [UNIT] key to select filter range amend(0-1-2-3-4-5-6-7),”2”is default setting; press [ZERO] key to select zero range whenturn on the scale, press [UNIT] key to select percent (PZR 2, PZR 5, PZR 10.PZR 20); press [ZERO] key to set zero range, press [UNIT] key to select percent(KZR 3,4,5,10); press [ZERO] key to set TARE range, press [UNIT] key selectpercent (KTR 50 or KTR 100); press [ZERO] key to enter overload protectionsetting, press [UNIT] key to select overload protection value (9d OVR-1 OVR-2OVR-10 OVR); press [ZERO] key to set beep function, press [UNIT] key to chooseturn on or turn off the beep, “b2 ON” means activate the beep, “b2 OFF” meansinactivate the beep; press [ZERO] key to unite the function of TARE and ZREO,press [UNIT] to switch between them. “ZT ON” means unite function activate,“ZT OFF” means unite function inactivate. press [ZERO] key to enter auto offfunction setting,display shows A xxx,press [UNIT] key to select auto off time(3,5,10,off). Press [ZERO] to select backlight, the display will show L Aut, press[UNIT] to select X value (X stands for AUT, OFF, ON), OFF stands for inactivatebacklight function, ON stands for the backlight is always make function. AUTOstands for auto backlight.4. Press [ZERO] to return to weighing mode. |
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine