ADTRAN Total Reach DDS-DP 5 Series Installation And Maintenance Manual

Also see for Series 5 Total Reach DDS-DP: Installation and maintenance guide Installation and Maintenance

ADTRAN Total Reach DDS-DP 5 Series Installation And Maintenance Manual Manual pdf 1 page image

161433105L1-5F Section 61433105L1, Issue 61. GENERALThis practice provides installation and maintenanceprocedures for the ADTRAN Series 5 Total ReachDDS-DP All-Rate DDS Dataport. Figure 1 is anillustration of the ADTRAN Series 5 Total ReachDDS-DP, P/N 1433105L1.Revision HistoryThis document has been revised to incorporate theresponse to the loopback pushbutton function of theDDS-R ACE remote unit, and add reference to falselatching loopback prevention at 64 kbps.DescriptionThe ADTRAN Series 5 Total Reach DDS-DP is afunctional replacement for the SLC® Series 5 OCUDP, CLEI 5SCU48, delivering data at rates up to 64kbps using a single copper pair. Used in combinationwith the DDS-R termination unit, the Series 5Series 5 Total Reach® DDS-DPTotal Reach All-Rate DDS DataportInstallation and MaintenanceSection 61433105L1-5FIssue 6, June 2002CLEI Code: 5SC53X4F_ _Trademarks: Any brand names and product names included in this document are trademarks,registered trademarks, or trade names of their respective holders.DDS-DP can accommodate extended loop lengths,eliminating the need for DDS repeaters. The Series 5DDS-DP span powers the DDS-R located at thecustomer premises. The DDS-R converts the 2-wiresignal to the traditional 4-wire Alternate MarkInversion (AMI) signal for presentation to thecustomer.The DDS-DP occupies a single channel position in theAT&T® SLC Series 5 or Series 5 compatible channelbank. It provides the interface between a DS0 timeslot of the T-carrier data stream and the 2-wiremetallic loop extending to the customer premises. TheSeries 5 Total Reach DDS-DP will interoperate overthe carrier system with another DDS-DP, OCU DP,DS0 DP, 1/0 DCS, or switch and can be located in anend office, hub office, intermediate office, or DigitalLoop Carrier (Figure 2). The 2-wire loop isconnected using the odd pair Tip (pin 31) and Ring(pin 32) on the Series 5 backplane.NOTEThe Series 5 Total Reach DDS-DP must be usedwith an appropriate DDS-R unit.CONTENTS1. GENERAL.......................................................... 12. OPTIONS ........................................................... 23. INSTALLATION ............................................... 34. TESTING ............................................................ 45. DEPLOYMENT GUIDELINES ........................ 56. MAINTENANCE ............................................... 67. WARRANTY AND CUSTOMER SERVICE ... 6FIGURESFigure 1. Series 5 Total Reach DDS-DP ................. 1Figure 2. Total Reach DDS Circuit Diagram .......... 2Figure 3. Option Switch .......................................... 2Figure 4. OCU Loopback at the DDS-DP ............... 4Figure 5. DDS-DP Bidirectional Loopback ............ 4Figure 6. DDS-DP Response to DDS-R ACELBK Button .............................................. 5TABLESTable 1. Option Settings ......................................... 2Table 2. Compliance Codes ................................... 3Table 3. LED Indication ......................................... 4Table 4. Cable Type and Temperature LossData@13.3 kHz ........................................ 5Table 5. DDS Insertion Loss Measurements ....... 5Figure 1. Series 5 Total Reach DDS-DP1433105SYNCSXFECRCNEDSUQMLBKMANSW2DDS-DP