Aastra 51i User's Quick Start Manual

Also see for AastraLink Pro 160: Administrator's guide Administrator's guide User guide User guide

Aastra 51i User's Quick Start Manual Manual pdf 1 page image

AastraLink Pro 160 User’s Quick Start Guide - Phone Setup41-001134-04 REV 00Identify Your Network Installation OptionFor Ethernet networks thatDO NOT supply power to the phone:- Use the 48V AC Power Adapterto connect from the DC power porton the phone to a power source.- Use the Ethernet cable (supplied)to connect from the phone to anetwork jack.For Ethernet networksthat supply in-line power tothe phone (IEEE 802.3af):- Use the Ethernet cable (supplied)to connect from the phonedirectly to the network.- No 48v AC power adapterrequired.For Ethernet networks that DO NOTsupply power to the phone:- Use a Power over Ethernet (PoE)power injector.- Use the Ethernet cable (supplied)to connect from the phone to thePoE power injector.- Use an additional Ethernet cablefrom the PoE to the Network jack (not supplied).NOTE: The optional PoE and Ethernetcable are available from your Aastradealer as optional accessories(p/n D0023-0031-00-00 andp/n D0061-0065-00-00, respectively).This quick start guide is designed tohelp you quickly set up and use yourIP phone in an AastraLink Pro 160network. The complete documentationset is available online at:http://www.aastratelecom.com/support53i 55i57iXferConfL2L3L135iConf ServicesXfer IcomABC DEFGHI JKL MNOPQRS TUV WX YZ1436257 980* #GoodbyeOptionsHold RedialL1 L2 L3 L435iConf ServicesXfer IcomABC DEFGHI JKL MNOPQRS TUV WX YZ1436257 980* #GoodbyeOptionsHold RedialL1 L2 L3 L457i CTServices SaveDelSwap51iWall MountDrilling TemplateasdassaasdadsdaHandset HandsetCordMounting Templateand HardwareEthernetCablePower AdapterThe 5i Models also have these:Base Legs Small ProgrammableKey Card (53i)Large ProgrammableKey Card (55i)The 9143i, 9480i, and 9480i CT Models also have these:Base Stand Programmable Key Cardand Plastic Lens (33i only)9143i 9480i 9480i CTNumber Cardand LensThe CT Models also have these:Power Adapter(for charging cradle)Belt Clip(for cordlesshandset)Battery(for handset)Charging Cradle(for cordlesshandset)Install Your Phone on a Desktop or a WallTo install the phone on a desk:5i Series PhonesAttach each leg to the back of the phone by inserting the tabs on the leg into theslots on the bottom of the phone. There are three pairs of leg slots on each cornerof the phone; each leg uses two pairs of slots when attached. (See Figure A)There are a total of 4 viewing angles (by reversing the legs, the incline on the phonecan be changed). (See Figure B).9143i, 9480i, 9480i CT Phonesonm1. Attach the stand by inserting the tabs on the stand (marked with ) into the slotson the bottom of the phone. For a higher viewing angle, use the slots marked .For a lower viewing angle, use the slots marked .2. Push the stand towards the phone until it snaps into place. (See Figure C).Figure BFigure ATo install the phone on a wall:1. Use the wall mount drilling template to locate and mark the positionfor the mounting screws on the wall.2. Drill the holes and insert the mounting screws (insert the wall anchorsbefore inserting the mounting screws if required).3. Coil the cables into the spaces provided on the back of the phone.4. Connect the Ethernet cable to the wall network jack.5. Place the wall mount holes on the back of the phone over the screwheads on the wall and pull down to lock the phone in.NOTE: Before installing the phone on the wall, connect the handset cord to the handset;connect the other end of the cord into the handset jack on the back of the phone. Usesteps 3 and 4 to connect all other cables to the phone. If you have a phone wall plate withpegs already installed on your wall, skip steps 1 and 2. Refer to Figures D and E.Figure CFigure D(5i Series Phones) Figure E(9143i, 9480i, 9480i CT Phones)1Connect the supplied Ethernet cableto the port (on 9143i, 9480i, and9480i CT phones) the LAN port (on 5i phones).lConnect the other end of theEthernet cable to the Ethernethub/switch or the network jack.To Network9143i, 9480i, 9480i CT Phones5i Series PhonesTo Network9143i, 9480i, 9480i CT Phones5i Series Phones3 1.2.k WARNING: This will disconnect your network connection.Connect the Ethernet cable from the phone to the Network Jack.BAReconnect the cable previously removedin step "B" to the back of the phonemarked with ; (9143i, 9480i, 9480i CT phones)COther Network DevicesTo OtherNetwork DeviceConnect Your Phone to the AastraLink Pro 160 NetworkIf you already have a network device, such as your computer,connected to the Network Jack where you are installing thephone, you will need to temporarily disconnect it from theNetwork Jack. To OtherNetwork Deviceor PC (5i Series phones).1.2.NOTE: The phone begins the startup process when power is first connected.NOTE: If your Ethernet network DOES NOTprovide power to the phone (either from theswitch, or using an inline power injector),you must use the supplied 48v AC adapterto power the phone. Connect the 48v adaptercable into the phone’s power connector andplug the adapter into an AC power source.BA Phone Powered by InlinePower from the NetworkPhone Powered by48V AC Power Adapter C (Optional) Phone Poweredby PoE Power InjectorNOTE: Before installing the phone on the desk, connect the handset cord to the handset;connect the other end of the cord into the handset jack on the back of the phone.To install the cordless handset:1. Attach the charging cradle power adapter to thecharging cradle and plug the other end into anon-switched AC outlet. (Figure F)2. Turn the cordless handset face down, remove theback cover, and install the battery. (Figure G)Replace cover.3. (optional) Clip the belt clip onto the back of the phone.Figure FFigure GSupported Aastra SIP IP Phone Models Optional Aastra IP Phone Expansion Modules536MProvides up to 36 additional softkeysto the 53i, 55i, 57i, and 57i CT560MProvides up to 60 additional softkeysto the 55i, 57i, and 57i CTSIP IP Phone Piece PartsAll models have these:21

/ 2

Related manuals for Aastra AastraLink Pro 160