Abe CS8096 User Manual
  |
CS8096Bluetooth® HeadsetUser ManualUser Manual!!Charging the batteryTurning on the HeadsetTurning off the HeadsetThank you for buying new CS8096 Headset. Before first time use, it isimportant to charge the battery for 12 hours.While the Headset ( HS ) is powered down, press and hold S1 for 2 seconds. A lowtone followed by a high tone will indicate that the HS is powered up. Green LED willturn on for 1 second. Afterward, green LED will flash every 3 seconds.While the HS is powered up, press and hold S1 for 3 seconds. A high tone followedby a low tone will indicate that the HS is powered down. And the LED will keep onRed until S1 is released.Bluetooth!1Headset pictures..............................................................................................................1Charging the battery.........................................................................................................1Turning on the Headset....................................................................................................1Turning off the Headset....................................................................................................1Putting Headset in Pairing Mode......................................................................................2Establishing Link..............................................................................................2Answering incoming calls.................................................................................................2Transferring calls..............................................................................................................2Muting the microphone.....................................................................................................2Ending calls.....................................................................................................................3To make a new call using voice dialing.............................................................................3Redialing last dialed number............................................................................................3Rejecting incoming call.....................................................................................................3Adjusting speaker volume................................................................................................3Ear Hook orientation........................................................................................................3Bend the ear hook to fit your ear.......................................................................................4Putting way.......................................................................................................................4Low-battery indication......................................................................................................4Charging and recharging the battery.................................................................................4Charging Connection Diagrams....................................................................................5Voice Over Internet Protocol (VoIP) Application..............................................................5FCC Interference Statement...........................................................................................6BluetoothMicrophoneSpeakerEar hookLockOn Off S1/ ( )Volume Up (S2)Volume Down S3( )LEDDC Socket!!!!Putting Headset in Pairing ModeEstablishing LinkAnswering Incoming CallsTransferring CallsMuting the microphoneMake sure the HS is fully charged and charging cable disconnected from it beforepairing starts. While the HS is powered off, press and hold S1 for 8 seconds. Redand Green LEDs flashing alternately will indicate that the HS is in Pairing Mode.Follow the operating instructions for your mobile phone to start thepairing process. Typically, this has to be done by going to a setup or connectmenu and then selecting the options to discover devices.may take several seconds to establish a connection.Your phone’s display should indicate that it has found the “CS8096” headset andasks if you want to pair it. You should confirm this. The phone’s display wouldprompt you for a passkey or PIN. Enter a sequence of “0000”.The headset LED will flash Green every 3 seconds, indicating successful pairing.Usually the phone will also ask whether you want to change the headset’s name.We recommend you should approve the CS8096 name and not change it. Youcan pair as many headsets and devices as you wish in your mobile phone.If pairing does not occur as expected. Turn the headset and phone off and wait for10 seconds. Turn the headset and phone on again and repeat all steps frombeginning.After pairing, the mobile phone will show “connect”, then please select “YES” toestablish the link Now you are ready to make and answer calls on the HS. Forother phones, please follow the operation manual to establish the link.When an incoming call is present, the HS will ring . Pressing S1 will answer thecall. The green LED will continue to flash fast while the call is in session. (Onceevery second)(For Nokia 3650 or equivalent models)When you are in session, calls can be transferred from the phone to theHS and from the HS to the phone.To transfer a call from the phone to the HS: press S1 once, the call willbe transferred to the HS.To transfer a call from HS to the phone, please follow the operatinginstructions of your phone.Pressing both S2 and S3 buttons simultaneously for about a second, themicrophone will be muted. A periodic beep tone will be heard while the mutefunction is active.When the microphone is muted, press on both S2 and S3 buttons simultaneouslywill end the mute function and the periodic beep tone will stop.BluetoothBluetooth BluetoothBluetoothBluetoothBluetoothBluetoothTo mute the microphone during an active callTo end the mute functionBluetooth.!2!!!Ending CallsTo make a new call using voice dialingRedialing last dialed numberRejecting incoming callAdjusting Speaker VolumeWhile a call is in session on the Headset, pressing S1 will disconnect the call.After the call is disconnected, the green LED will flash normally.1.Make sure the voice dialing function is probably set up in the Mobile phone andit is within the range of the HS. Press S1 on the HS shortly.2.After the beep tone on the HS, make a voice dial as you normally would bysaying the name of the person on the HS. The call will be connected in a fewseconds.1.Make sure the voice dialing function is probably set up in the mobile phone andit is within the range of the HS. Press S1 on the HS shortly.2.After the beep tone on the mobile phone, make a voice dial as you normallywould and the call will be connected in a few seconds.(Support handsfree profile mobile only. For Nokia3650, Siemens S55, or equivalent models)To redial the last dialed number, press and hold S3 for 2 seconds. short low toneswill indicate an attempt to redial.(Support handsfree profile mobile only. For Nokia3650, Siemens S55, or equivalent models)When there is an incoming call and you want to reject it, press the buttons S1 andhold it until you hear a long beep tone, then release it.While a call is in session, pressing and releasing S2 will increase the speakervolume; pressing and releasing S3 will decrease the speaker volume on the HS.There is a key tone to indicate volume increase or decrease. However, awarning tone will be heard when the volume level reaches its maximum orminimum.When using a Bluetooth mobile phone:When using a mobile phone without Bluetooth built-in and requiring a Bluetoothdongle:!!! Ear Hook orientationIf you want to change the orientation of ear hook, please follow the following steps.1) Detach the ear hook from the phone2) Select the orientation you want (left or right), and attach the ear hook and lock it3 |
Related manuals for Abe CS8096
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine