Abexo INDUS6 Assembly And Operating Instructions Manual
1 - MAIN FEATPower supply: 12-36 V ac/dc.- Decoding: HCS with Manufacturer Code ABTECNO.- Maximum number of remote controls that can be stored 500. Output: no.2 relays ofsignal (max 1A).2 - POWERING UP THE RECEIVERThe receiver is equipped with two LEDs (LED A and LED B) to signal thesuccessful power supply to the board.When the receiver is first turned on, these two leds light up briefly and thenturn off.3 - NORMAL OPERATIONDuring normal use, the 2 LEDs (LED A and LED B) are associated with theoperation of the 2 output relays. Thus led A is associated with theoperation of relay A while led B is associated with the operation of relay B.With the receiver powered and at rest, the leds will be off and will onlylight up when a channel of the radio control will activate the respectiverelay. With this function you will always have a visual indication of thecorrect operation of the receiver for each relay.NB: it is not possible to drive the outputs during programming or cancella-tion.4 - RADIOCOMMAND MEMORIZATION The maximum number of radiocontrols that can be stored is 500 units. To store the radio controls in thereceiver, programming mode must be enabled by holding down the P-Abutton on the receiver until the LEDs provide a succession of visual signalsa 2-second intervals, following the following order: LED A, LED B, LED A+Band then repeat the sequence in the same order.Signals that provide an indication of which relay is to be activated with theremote control to be stored (led A relayA only, led B relay B only, led A+B bothrelays A and B).Once you have identified the choice ofthe type of relay output desired,release the P-A button at the relevantvisual indication of the LEDs.At this point it is possible to memorisethe radio control by pressing thebutton that you wish to associate with the selected relay (the button of theradio control that has to be memorised must be pressed until the tworelays both light up for a few seconds to confirm correct memorisation).NB: To store new radio controls, it will be necessary to repeat the operationfrom the beginning, by pressing the P-A button again.5 - DELETION OF A REMOTE CONTROLTo delete the memory of a remote control incorrectly inserted in thereceiver or to change its pairing to a particular relay you must carry out thefollowing procedure:- Keep the P-A button pressed until the leds provide a succession of visualsignals, every 2 seconds, in the following order: led A, led B, led A+B thenrepeat the sequence in the same order. In this cancellation procedure it isnot as important to select the relay as in the memorisation procedure soyou can release the P-A button as soon as LEDs A and B provide visualindication.- Once P-A button has been released, press P-B button until the two leds Aand B will light up.- Press any button on the remote control to be erased from the receivermemory, until the two LEDs turn off, thus indicating correct deletion.At the end of this procedure, none of the remote control keys will beno longer recognised by the receiver.NB: During these steps, a press of the P-A button on the receiver determi-nes the exit from the erase mode.MADE IN ITALYINDUS6cod.APE-550/4006INDUS RXINDUS RXcod.APE-550/4033IND-00007 - 2/2024AB Tecno SrlVia Cicogna 95 - 40068 San Lazzaro di Savena (BO)Tel: +39 051 6259580 - fax: +39 051 6259600info@abtecno.com - www.abexo.techMultifrequency transmitter and receiverAssembly and operating instructionsLed BLed APulsante P-BPulsante P-AANTENNAGND+12/36 VAC/DCGNDRELAYS 1 ( N.A.)RELAYS 2 ( N.A.) |
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine