Abexo SH230LUX User Instructions
CONTROL UNIT FOR ROLLER SHUTTERSWITH INTEGRATED COURTESY LIGHTSH230LUXTechnical data- Power supply 230Vac +/-10%- Motor power 1350W (1HP)- Working time: adjustable from 0.5 min to 2 min.- Pause time: adjustable till max 3 min.- Courtesy light time: adjustable to max 3 min.- Safety edge input: 8k2 ohm or NC contact- Courtesy light output: 12 V- Flashing light output: 12 V- Code combination: 72 million- Number of transmitters: 25- Radio code programming: self-learning- Frequency: 433.92 Mhz- Sensitivity: greater than -100dbm- Antenna: built-in- Operating temperature: -10°C, +70°C- Application range: standard 50 mt - man present 10 mtAPE-528/1230USER INSTRUCTIONSCode: AB9-00013 - rev.0 of 11/2021WARNINGS FOR INSTALLER - GENERAL SAFETY RULES1. Read the instructions carefully before proceeding with the installationof the control unit.2. Keep these instructions for any future reference.3. This product is designed and manufactured exclusively for the useintended and indicated in this documentation. Any other use notexpressly indicated could impair the integrity of the product and/orrepresent a source of danger.4. For the safety, you must carefully follow the instructions provided inthis manual. Incorrect installation or incorrect use of the product maycause serious personal injury.5. Materials used for packaging should not be left within the reachof children, as they are potential sources of danger, and should beproperly disposed of.6. AB Tecno Srl disclaims all liability for any consequences resultingfrom improper use or use other than that for which the device wasdesigned and constructed.7. AB Tecno Srl is not responsible for non-compliance with applicableEC standards for motorized locks, as well as any deformation that mayarise in use.8. Do not install the equipment in an explosive atmosphere: thepresence of gas or inflammable fumes constitutes a serious source ofsafety hazard.9. Installation must be effected in accordance with EN 12453 and EN12445. For non-EEC countries, in order to achieve a sufficient levelof safety the above standards must be observed in addition to theindividual national regulatory references.10. Before working on the system, disconnect any batteries anddisconnect the power supply.11. It is advisable to provide for the presence of an omnipolar switch withcontact opening distance equal to or greater than 3 mm on the mainspower supply of the automation. We recommend the use of a circuitbreaker of 6A with an omnipolar breaker.12. Check that there is a differential circuit breaker upstream of thesystem. With a 0.03A threshold.13. Check that the grounding system is properly made, and connect themetal parts of the enclosure to it.14. Even automations that have an internal safety anti-crushing functionrequires functional check in all cases in compliance with the standardsindicated in Section 9.15. Safety devices (EN 12978 standard) enable the protection of anyhazard areas from mechanical Risks related to movement, such ascrushing, conveying, shearing and lifting.16. For each installation, we suggest using at least one signaling light (ex.flashing lights), as well as a warning sign properly f xed and clearlyvisible.17. AB Tecno Srl disclaims any responsibility related to the safety andproper operation of the automation.18. The installer must provide the final user with all information regardingmanual operation of the automation in case of emergency.19. During operation, do not allow children or others to stand near thesystem during operation.20. Keep out of the reach of children any remote control or device toprevent the possible unwanted operation of the automation.21. The transit of people and vehicles is permitted only and exclusivelywhen the automation is fully opened.22. The User of the automation must refrain from any attempt to repairand/or direct intervention and refer exclusively to qualified personnel.Otherwise, AB Tecno Srl declines all responsibility for any possibleconsequences.23. Anything not expressly indicated in these instructions is not allowed.1DECLARATION OF EU CONFORMITYProduct: SH230LUXManufacturer: AB TECNO S.r.L. - Via Cicogna, 95 - 40068 San Lazzaro di Savena (BO)The Manufacturer declares under its own responsibility that the product coveredby the declaration meets all the provisions applicable in the following Directives:2014/35/EU - on the harmonization of the laws of the Member States relatingto the making available on the market of electrical equipment intended for usewithin certain voltage limits.2014/30/EU - for the harmonization of the laws of the Member States relatingto electromagnetic compatibility and complies with the relevant harmonizationlegislation of the Union: CEI EN 60947-1: 2008/A1: 2012/A2: 2015, CEI EN 60947-5-1: 2005/A1: 2010.Bologna, 15/10/2021 AB TECNO’s CEOUlisse PaganiABEXO è un marchio registrato di proprietà diABTECNO srl - Via Cicogna 9540068 San Lazzaro di Savena (BO)info@abtecno.comwww.abexo.techAUTOMATION ACCESSORIESABEXO is a registered trademark owned by |
Related manuals for Abexo APE-528/1230
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine