Absinthe 19006-01 Quick Manual
  |
LED CONTROLLERPRI:Uin=12-36VDCIin=32.5ASEC:Uout=4x(12-36)VDCIout=4x8APout=4x(96-288)WTEMP RANGE:-20℃-+50℃19006-01V+G-R-OUTPUT SIGNALCH12DC INPUT12/36VDCV+V-B-3B-3W-4LearningSwitchLED CONTROLLERPRI:Uin=12-36VDCIin=32.5ASEC:Uout=4x(12-36)VDCIout=4x8APout=4x(96-288)WTEMP RANGE:-20℃-+50℃19006-01V+G-R-OUTPUT SIGNALCH12DC INPUT12/36VDCV+V-B-3B-3W-4LearningSwitchLED CONTROLLERPRI:Uin=12-36VDCIin=32.5ASEC:Uout=4x(12-36)VDCIout=4x8APout=4x(96-288)WTEMP RANGE:-20℃-+50℃19006-01V+G-R-OUTPUT SIGNALCH12DC INPUT12/36VDCV+V-B-3B-3W-4LearningSwitchLED CONTROLLERPRI:Uin=12-36VDCIin=32.5ASEC:Uout=4x(12-36)VDCIout=4x8APout=4x(96-288)WTEMP RANGE:-20℃-+50℃19006-01V+G-R-OUTPUT SIGNALCH12DC INPUT12/36VDCV+V-B-3B-3W-4LearningSwitchLED CONTROLLERPRI:Uin=12-36VDCIin=32.5ASEC:Uout=4x(12-36)VDCIout=4x8APout=4x(96-288)WTEMP RANGE:-20℃-+50℃19006-01V+G-R-OUTPUT SIGNALCH12DC INPUT12/36VDCV+V-B-3B-3W-4LearningSwitchUniversal series RF ReceiverInputVoltageOutputCurrent12-36VDC 4x(96-288)W4x8AOutputPowerWaterproof grade: IP20Radio Frequency : 869.5/916.5/434mhzFunction introductionProduct Data• DO NOT expose the device to moisture.• DO NOT install with power applied to device.Safety & WarningsLED CONTROLLERPRI:Uin=12-36VDCIin=32.5ASEC:Uout=4x(12-36)VDCIout=4x8APout=4x(96-288)WTEMP RANGE:-20℃-+50℃19006-01V+G-R-OUTPUT SIGNALCH12DC INPUT12/36VDCV+V-B-3B-3W-4LearningSwitchLearning Key:Paring with RF remoteDC Power inputCH 1:R/WW output(-)CH 2:G/CW output(-)CH 3:B/WW output(-)Common Anode Output(+)Master/SlavejumperCH 4:W/CW output(-)Important: Read All Instructions Prior to InstallationWiring DiagramLNGV+V-OUTPUTINPUTAC Power50/60Hz12V/24V/36VCV PSUIf Connect with RGBW LED StripV+ V+R- R-G- G-B- B-W- W-V+ V+1- V-2- V-3- V-4- V-If Connect with Single Color LED StripV+ V+WW WWCW CWWW WWCW CWIf Connect with Dual Color LED Strip1. The receiver has both master and slave functions which can be set with a jumper. Short circuit of the jumpermeans master function, and open circuit means slave function. Once short circuit the jumper on a receiver,please power off and power on the receiver to enable master function. Setting master and slave enables perfectsynchronization of color changing effects.2. Set one receiver as master and pair it to any zone of a remote, and this zone shall only have one receiverwhich works as master. Set all other receivers as slave and pair them to other zones of the remote, and multiplereceivers can be paired to each zone. Then choose all zones on the remote and play the color changingeffects, the master will send sync signal to the slaves to achieve perfect synchronization. The max. syncdistance between the master and any slave is within 30m.Master and Slave Setting:Pair/delete the pairing with RF remote2.Pair RF Receiver with RF remote: please refer to the instruction of the remote that you would like to pair with.3.Delete the pairing:(1)Wire up the RF receiver correctly, power on.(2)Press and hold down the “ Learning Key” button on receiver for over 3 seconds until the connected lightflashes, which means well deleted.1.Do wiring according to connection diagram.RemarksConstant voltageSize(LxWxH)170x59x29mm1) When total load of each receiver is not over 20A2) When total load of each receiver is over 20AV+ V-LNGV+V-OUTPUTINPUTAC Power50/60Hz12V/24V/36VCV PSUV+ V+1- V-2- V-3- V-4- V-If connect with Single Color LEDV+ V-LNGV+V-OUTPUTINPUTAC Power50/60Hz12V/24V/36VCV PSUV+ V+WW WWCW CWWW WWCW CWIf connect with Dual Color LEDMax. 20A20.05-3.3mm(12-30AWG)ConnectorCurrent Rating Wire Size19006-01 |
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine