Accedian Skylight Flex 25 Hardware Installation Manual
  |
Compliance Statements423-050-00-EN, Revision 3Published: 2023-05-05FCC Class AThis equipment has been tested and found to comply with the limits for a ClassA digital device, pursuant to part 15 of the FCC Rules. These limits are designedto provide reasonable protection against harmful interference when theequipment is operated in a commercial environment. This equipment generates,uses, and can radiate radio frequency energy and, if not installed and used inaccordance with the instruction manual, may cause harmful interference to radiocommunications. Operation of this equipment in a residential area is likely tocause harmful interference in which case the user will be required to correct theinterference at his own expense.VCCI–ANote: Package can contain other ordering options. See the Ordering Guide for more details.Attention: This product, like all electronic products, uses semiconductors thatcan be damaged by electrostatic discharge (ESD). Always observe appropriateprecautions when handling.Warning: Potential for damage to equipment or personal injury.ConventionsAttention: This symbol indicates that the surface is hot and to use caution toavoid touching it.Protective grounding pointこの装置は、クラスA情報技術装置です。この装置を家庭環境で使用すると電波妨害を引き起こすことがあります。この場合には使用者が適切な対策を講ずるよう要求されることがあります。Package ContentsUnit DescriptionSkylight Flex 25™HARDWARE INSTALLATION GUIDESpecial considerationsFront Panel (With Synchronization Option)Basic Contents• Unit (1x)• Power Kit Accessories (1x):¯ DC Unit: 2x Input Mating Connectors¯ AC Unit: 1x Power Cord Retainer Clip• This Hard Installation Guide (1x)System VentilationHolesFresh Air IntakeSynchronization IN/OUT (Optional)3x SMA Connectors: GNSS Antenna Input, Sync IN & Sync OUTManagement Port 1x RJ45 Connector (10M/100M/1GbE)Console Port or DryContact Inputs1x RJ45 Connector (RS-232 or 2 Dry Contacts)Note: Cannot be used at the same time.Console Port 1x USB Mini-B Connector (USB 2.0)Traffic Ports 4x SFP28 Connectors (1/10/25GbE)Auxiliary Port 1x SFP10 Connector ((1/10GbE)Reset Button System ResetNote: Press the RST button for > 5 seconds to reset the unit tofactory defaults.SynchronizationLED (Optional)ANT (Green):-ON: GNSS is enabled and is locked on satellite-BLINKING: GNSS is enabled and searching for satelliteSYNC IN (Green):-OFF: No Synchronization Input Detected-ON: Synchronization Input DetectedSYNC OUT (Green):-OFF: Synchronization Output De-Activated-ON: Synchronization Output ActivatedALM (Red):-OFF: No Sync. Module Alarm Condition-ON: Sync. Module Alarm ConditionMIN MAJ CRIT LED Minor (Yellow), Major (Red) or Critical (Red) alarm condition:OFF: No AlarmON: Alarm ConditionStatus LED (Green) ON: Normal operationFlashing: The unit is bootingPower LED (Green) ON: Normal operationLink LED (Green) ON: Link is active / OFF: Link is inactiveActivity LED(Green)OFF: No Tx/Rx ActivityBLINKING: Port is receiving/transmitting dataInstalations where a unit with the GNSS may be exposedto voltage in excess of 10kV, additional protection, such asexternal surge suppressor, may be necessary.PIN # Signal1 Dry Contact#12 Not Connected3 RS323 TX Data4 Ground5 Ground6 RS232 RX Data7 Not Connected8 Dry Contact#2The Dry Contacts Interface is strictly Safety ExtraLow Voltage (SELV).Note: See the User Material for more details. |
Related manuals for Accedian Skylight Flex 25
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine