Accell K078C-008B Manual
  |
Model Number:K078C-008BUltraAV® HDMI Splitter and DistributionAmplifier with HDBaseT LiteREAD ME FIRST – SETUP INSTRUCTIONSThank you for purchasing the Accell UltraAV HDMIDistribution Amplifier. This product is designed to providean exceptional performance and value. Please review themanual before operating and retain for future reference.- CAUTION -1. Ensure the unit has sufficientventilation. Do not coverventilation openings. Do not installin a confined space.2. Do not operate near sourceof heat. Do not stack on top,underneath or between other heatgenerating unit/s including otheramplifiers.3. Unplug power adapter if notused for an extended period.4. To prevent damage from powersurges, the unit should be pluggedinto a surge protector or surge pro-tected power source.5. Do not use near liquid or areasof heavy moisture.6. Clean unit with a clean and drycloth only.7. This unit cannot be serviced inthe field. Contact Accell if service isrequired.8. Do not open case, risk of shock -shock hazard.9. Do not modify power cord or usethe product if the power cord isdamaged.IntroductionThe UltraAV HDMI Distribution Amplifier (Splitter) featuring HDBaseTLite accepts a signal from a single HDMI enabled audio/video source andsplits the single input into 4 HDMI outputs. The audio/video signal ismirrored on up to 4 HDMI displays, monitors, projectors or TV’s.Over-Current and Over-Voltage ProtectionThe circuit boards are equipped with both over-current and over-voltageprotection and will automatically power down if encountered. The circuitboards will restore automatically once the excessive current or voltagehas passed.Package Contents●HDMI Distribution Amplifier (Splitter) ●1 Power Adapter (for Matrix)●4 HDBaseT Receivers ●4 Power Adapters (for Receivers)●Owners Manual ●4-Pair IR-TX and IR-RX1x4 HDMI Splitter with HDBaseT LiteModel: K078C-008BSpecifications● Connect 1 HDMI Source to up to 4 HDMI Displays● Supports HD resolutions up to 1080P and 3D● HDMI 1.4a, HDCP 1.2 compliant● Data transfer speed of 6.75Gbps (225MHz)● Audio formats supported: DTS-HD 7.1, Dolby True-HD 7.1● Deep color up to 36-bit● Maximum HDMI input/output cable length: Up to 16ft./5m● Maximum Cat5e/6 output cable length: Up to 230ft./70m● Shelf or surface mountable● 9V DC, UL Listed Power Supply for 1x4 Splitter Unit● 5V DC, UL Listed Power Supplies for Receiver Units (4 Total)● Input AC: 50Hz to 60Hz, 100-240V● Splitter dimensions: 10.9”W x 1.1”H x 6.1”D (277W x 28H x 156D mm)SetupNote: All Cat5e/6 cables must be terminated to 568B standards.Unsheilded (or properly terminated sheilded cable), solid core Cat5e,Cat6, Cat6e, Cat7 or Cat7e cable can be used. Stranded core is notsuggested as it can reduce signal transfer. Recommended to use acontinuous length of cable terminated at the matrix and receiver ends.With the splitter power switch in the OFF position, connect the HDMIHigh Speed cable from the HDMI Output of the audio/video source to theHDMI Input located on the rear of the splitter.Tips: Use the shortest length HDMI cables possible in each pointin the installation. Use only High Quality and High Speed HDMIcables.Next, connect a Cat5e/6 cable to the HDBaseT Out 1 port on the rear ofthe splitter. Connect the other end of the Cat5e/6 cable to the HDBaseTIN port on the rear of the HDBaseT receiver positioned near the TV. Runa short, High Speed HDMI cable from the HDMI Out port on the receiverto the HDMI In port on the TV. Plug a provided power adapter into anAC outlet and the other end into the HDBaseT receiver. Using the samesteps, connect the remaining displays to the splitter.Important: The HDBaseT Receivers when operating are warm and dorequire space around the housing for air circulation and coollng. Do notenclose the HDBaseT receiver. If placed behind a component such as aTV, ensure that there is adequate space for air circulation and ambientcooling and that there is no heat being generated and transmitted to thereceiver from the other device. Damage caused by improper placementand overheating of the splitter or the receiver is not covered by theproduct warranty.On initial power on, all LED lights on the splitter should come on solidblue. If less than the maximum number of Displays are connected tothe splitter (not all the outputs are used) there will be no correspondingHDMI OUT blue LED for the unused output. Blue lights will only appearfor devices connected.The HDBaseT Receiver has 4 LED indicators:1. HDCP: A solid LED indicates that the HDCP handshake between thesource and display has been authenticated.2. Link: Indicates a connection between the Matrix and the Receiver.3. Mode: A flashing LED indicates correct operation of the system.4. Power: A solid LED indicates power to the receiver.LED Indicator Lightsspecifications continued:● Receiver dimensions: 4.4” W x .9” H x 3” D (112W x 23H x 76D mm)● Operating temperature range: 5 to 131°F (-15 to 55°C)● Operating humidity range: 5% to 90% RH (no condensation) |
Related manuals for Accell K078C-008B
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine