AccessPRO INDUSTRIAL XB220H06K Technical Instructions
XB220H06KTECHNICAL INSTRUCTIONSWARNINGS FOR THE INSTALLER – GENERAL SAFETY OBLIGATIONS1ATTENTION! It is very important for the safety of people to follow all instruc-tions strictly. A wrong installation or use of the product could cause seriousdamage to people.17ªéåËÃåÄÞå½½åËÄÞªË齪ôå½ÞåËĽ¥ªåÄ¥ ôĸĪģąÞªÄ¥½¥ªåÞintegrated in the crosshead of the bollard) and a signal placard, along with the devicequoted at point “16” 2 Read carefully this manual before starting installation and save itfor future reference. 18 In each automatic installation the installer must consider.2 Read carefully this manual before starting installation and save it for futurereference. 18 In each automatic installation the installer must consider and install appropriate safetydevices.3 Packaging materials (i.e. plastic, polystyrene, etc.) must be out of children’sreach, because potentially dangerous. 19 For maintenance works use only original parts supplied by AccessPRO INDUSTRIAL.4This product has been designed and manufactured exclusively on the purposeindicated in this manual. Any different use not here indicated could damage theintegrity of the product and/or be potentially dangerous.20AccessPRO INDUSTRIAL is not responsible for safety and good functioning of theproduct , in case of use of components not manufactured or distributed by AccessPROINDUSTRIAL.5 AccessPRO INDUSTRIAL is not responsible for any damage caused by impro-per or different use from the indicated one. 21 ËÄËå××½ûÄûÃËĄåËÄåËåª×ÚåÞËÃ×ËÞÄ¥åªéåËÃå ×ÚËéåÞÞ-PRO INDUSTRIAL.6 ËÄËåÄÞå½½åªôÄÄú×½ËÞôÚģgÞÄ¥/ÄąÃý ¥ÞÞËé½be not safe. 22The installer must provide the Customer with all information related to the manual relea-se of the automatic bollard in case of emergency and give the User a warning manualattached to the product.7 Installation must be according to the local Laws. 23 Do not allow children or others to stop close to the bollard during operation.8In order to have an adequate safety level in the extra-CEEcountries, in addiction to the national laws, the above mentioned laws must befollowed.24 Keep remote controls or other impulse-giving devices out of children’s reach, in order toavoid involuntary activation.9AccessPRO INDUSTRIAL is not responsible if someone does not observes thecorrect method of installation of the AccessPRO INDUSTRIAL products andrelated devices, included deformations coming during the use.25 Thoroughfare over the AccessPRO INDUSTRIAL bollard allowed only at completelowering of the bollard.10 Before any actions on the automatic installations take power off. 26Semiautomatic bollards are not adviceable for multiple installation (two or more) onmain streets where the frequent passage of vehicles over the lowered bollards canbreak the lock block and make the bollard lifting without control.11An Omni polar switch should be foreseen on the alimentation’ s net of automaticinstallations. Its connections should have an opening range of 3 mm. A magne-totermical differential with 6A Omni polar switch is adviceable27 The User must avoid any repairing actions or direct operations on the bollard, and mustÚÞÞåËÙé½ĄÄéåªËÚĀ×ÚÞËÄĽËĽûĪ12 Assure that a differential switch with 0,03° is present at thebeginning of the automatic installation. 28 Do not waste exhausted batteries in the garbage, but dispose them in the apposite con-tainers to allow recycling. Disposal costs have already been paid by the manufacturer.13The main electrical alimentation of the control unit of automatic installationsmust be connected directly to at the beginning of the apposite principal switchÞåÄÞåªËÄåÚ˽éÄåįéÞÄåĽąÃ½Þ××ÚËôû å½ÞåËÄˤåªéÚË×Ä/ÄÞååéåÞĪcªÃÄÞËÄË¤åªĄÚÞå½ÃÄååËÄ ½ÄÃéÞåminimum 3x2,5mm,but evaluated by the installer according to the number ofAccessPRO INDUSTRIAL bollards (400W each AccessPRO INDUSTRIALbollard) and the distance from the output point in order to guarantee a correctalimentation (230V +/- 10% for moving AccessPRO INDUSTRIAL bollard).29The product is packaged on Euro pallet; use pallets’ movers or shunters for movement;handlewith care.14 Test that the earthing is workmanlike and connect the metallic parts. 30 The product has been manufactured with IP 56 protection’s level, and could thereforebe stored everywhere; storage in internal or covered places is anyway preferable.15The automatic installations include a standard safety device: an inversionpressure switch in case of at least 40 kg of load. It is anyway necessary to testthe activation level every six months, according to what laws establish.31 The product does not require availability of spare parts; AccessPRO INDUSTRIAL’swarehouse can send by express any needed spare parts.16Safety devices (Law EN 12978) allow protection of potentially dangerous areaswhere activities such as squashing, conveyance, shearing are possible tooccur.32In case of maintenance and/or reparation, Pay attention not to give improper raisingsignals; to avoid any problems, disconnect the bollard’s moving by the switch set insidethe control management station.33 Everything not mentioned in this manual is not allowed. |
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine