AccuMed CMS-50D1 User Manual
  | |
Contents | 
IUser ManualInstructions to UserThank you very much for purchasing our product!This Manual is written and compiled in accordance with the council directive MDD93/42/EEC for medicaldevices and harmonized standards. The Manual is written for the current Pulse Oximeter. In case ofmodifications and software upgrades, the information contained in this document is subject to changewithout notice.The Manual describes, in accordance with the Pulse Oximeter’s features and requirements, mainstructure, functions, specifications, correct methods for transportation, installation, usage, operation,repair, maintenance and storage, etc. as well as the safety procedures to protect both the user andequipment. Refer to the respective chapters for details.Please read the Manual very carefully before using this equipment. These instructions describe theoperating procedures to be followed strictly; failure to follow these instructions can cause measuringabnormality, equipment damage and personal injury. The manufacturer is NOT responsible for the safety,reliability and performance issues and any monitoring abnormality, personal injury and equipmentdamage due to user’s negligence of the operation instructions. The manufacturer’s warranty service doesnot cover such faults.Due to continual re-inovation, the products you received may not be totally in accordance with thedescription of this User Manual. We would sincerely regret for that.This product is medical device, and can be used repeatedly.WARNING: An uncomfortable or painful feeling may develop if using the device ceaselessly, especiallyfor the microcirculation barrier patients. It is recommended that the sensor should not beapplied to the same finger for over 2 hours. For the individual patients, there should be a more prudent inspection in the measured part.The device cannot be placed on the edema and tender tissue. The light (the infrared is invisible) emitted from the device is harmful to the eyes, so the userand the maintenance man, cannot stare at the light. Testee cannot use enamel or other makeups. Testee’s fingernail should not be too long. Please peruse the relative content about the clinical restrictions and caution. This device is not intended for treatment.The User Manual is published by our company. All rights reserved.1 OverviewThe pulse oxygen saturation is the percentage of HbO2 in the total Hb in the blood, so-called the O2concentration in the blood. It is an important bio-parameter for the respiration.Many respiratory diseases will cause the body’s SpO2 to decrease, while the body automatic adjustmentdisorder caused by the anesthesia, big surgery trauma, and some of the damage caused by medicalexamination, are likely to lead to patient’s oxygen supply problems and reduce the body’s SpO2, resultingin patient dizziness, weakness, vomiting and other symptoms. Severe cases will threaten life. So knowingthe patient’s SpO2 in time will help doctor which has great significance in clinical medical area.The Pulse Oximeter features a small size, low power consumption, convenient operation, and portability.It is only necessary for patient to put one of his fingers into a fingertip photoelectric sensor for diagnosis. Adisplay screen will directly show measured value of Hemoglobin Saturation.1.1 Features Simple and convenient operation. The product is small in size, light in weight, and convenient to carry. Low power consumption.1.2 Major Applications and Scope of ApplicationThe product is applicable for use in family, hospital, oxygen bar, community medical treatment and sporthealth care (it is advised to be used before and after sports and it is not suggested to be used in theprocess of sport),etc.The product is not suitable for use in continuous supervision for patients.The problem of overrating would emerge when the patient is suffering from toxicosis which iscaused by carbon monoxide. The device is not recommended to be used under thiscircumstance.1.3 Environment RequirementsStorage Environmenta) Temperature: -40ºC~+60ºCb) Relative humidity: ≤95%c) Atmospheric pressure: 500hPa~1060hPaOperating Environmenta) Temperature: 10ºC~40ºCb) Relative Humidity: ≤75%c) Atmospheric pressure: 700hPa~1060hPa1.4 Safety1.4.1 Instructions for Safe Operations Check the main unit and all accessories periodically to make sure that there is no visible damagethat may affect patient’s safety and monitoring performance. It is recommended that the deviceshould be inspected once a week at least. When there is obvious damage, stop using it. Necessary maintenance must be performed by qualified service engineers ONLY. Users are notpermitted to maintain it by themselves. The oximeter cannot be used together with devices not specified in User’s Manual. Only accessoriesthat are recommended by the manufacture can be used with this device. This product has been calibrated before leaving the factory.1.4.2 Warnings Explosive hazard—DO NOT use the oximeter in environment with flammable gas such as someignitable anesthetic agents. DO NOT use the oximeter while the testee is undergoing a MRI or CT. The person who is allergic to the rope cannot use this device. The person who is allergic to rubber cannot use this device. The disposal of scrap instrument and its accessories and packing (including battery, plastic bags,foams, and paper boxes) should follow the local laws and regulations. Please check the packing before use to make sure the device and accessories are in accordancewith the packing list, or else the device may have the possibility of working abnormally. Please don’t measure this device with function test paper for the device’s related information.1.4.3 Attentions Keep the oximeter away from dust, vibration, corrosive substances, explosive materials, hightemperature, and moisture. If the oximeter gets wet, please stop operating it. When it is carried from cold environment to warm or humid environment, please do not use itimmediately. DO NOT operate keys on front panel with sharp materials. High temperature or high pressure steam disinfection of the oximeter is not permitted. Refer to UserManual in the relative Chapter for instructions of cleaning and disinfection. Do not have the oximeter immerged in liquid. When it needs cleaning, please wipe its surface withmedical alcohol by soft material. Do not spray any liquid on the device directly. When cleaning the device with water, the temperature should be lower than 60ºC. As to the fingers which are too thin or too cold, it would probably affect the normal measure of thepatients’ SpO2 and pulse rate. Please clip the thick finger such as thumb and middle finger deeplyenough into the probe. Do not use the device on infants or neonatal patients. The product is suitable for children above four years old and adults (Weight should be between 15kgto 110kg). The device may not work for all patients. If you are unable to achieve stable readings, please stopusing. The update period of data is less than 5 seconds, which is changeable according to differentindividual pulse rate. The waveform is normalized. Please read the measured value when the waveform on screen isequably and steady-going. Here this measured value is the optimal value. And the waveform at themoment is the standard one. If some abnormal conditions appear on the screen during test process, pull out the finger andreinsert to restore normal use. The device has normal life span of three years since the first electrified use. The hanging rope attached the product is made from Non-allergy material. If a particular group issensitive to the hanging rope, stop using it. In addition, pay attention to the use of the hanging rope.Do not wear it around the neck to avoid causing harm to the patient. The instrument doesn’t have a low-voltage alarm function. It only shows the low-voltage. Pleasechange the battery when the battery is dead. The device doesn’t have an alarm for exceeding a limit. Do not use the device in situations wherealarms are required. Batteries must be removed if the device is going to be stored for more than one month, or elsebatteries may leak. A flexible circuit connects the two parts of the device. Do not twist or pull on the connection.2 Principle of MeasurementFigure 1 Operating principlePrinciple of the Oximeter is as follows: An experience formula of the data process is established takinguse of Lambert Beer Law according to Spectrum Absorption Characteristics of Reductive Hemoglobin (Hb)and Oxyhemoglobin (HbO2) in glow & near-infrared zones. Operation principle of the instrument is:Photoelectric Oxyhemoglobin Inspection Technology is adopted in accordance with Capacity PulseScanning & Recording Technology, so that two beams of different wavelength of lights can be focusedonto human nail tip through perspective clamp finger-type sensor. Then measured signal can be obtainedby a photosensitive element, information acquired through which will be shown on screen throughtreatment in electronic circuits and microprocessor.3 Technical Specifications3.1 Main Performance1) SpO2 value display.2) Pulse rate value, bar-graph display.3) Pulse waveform display.4) Low battery indication: When the voltage is too low to work, the battery capacity indication appears.5) Automatically power off function: The product will automatically be powered off when there is nosignal within 5 seconds.6) Display format can be changed.3.2 Main Parameters1) SpO2 MeasuringRange:0%~100%Accuracy: ±2% in stage of 70%-100% SpO2, and meaningless when stage being smaller than 70%2) Pulse Rate MeasuringRange: 30 bpm - 250 bpmAccuracy:±2 bpm or±2% (select larger)3) Resolution: 1% for SpO2 and 1 bpm for Pulse Rate.4) Resistance to surrounding light: The deviation between the value measured in the condition ofman-made light or indoor natural light and that of darkroom is less than ±1%.5) Working voltage: DC 2.6V~3.6V.4 Installation4.1 View of the Front PanelFigure 2 Front view4.2 Battery Installation1) Refer to Figure 3 and insert the two AAA size batteries properly in the right direction.2) Replace the cover.Please take care with the batteries as improper insertion may damage the device. |
Related manuals for AccuMed CMS-50D1
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine