Axon Body 2 Quick Start Manual
Also see for Body 2: User manualUser manualQuick start guideQuick tips guideQuick start guide
  | |
Contents | 
Camera Operation LEDThe Axon Body 2 camera’s operation LED displays the system’s current operatingmode.Operating Mode Operation LEDRecordingRecovering interrupted video* Blinking redBuffering Blinking greenBooting up/powering downError state** Solid red*When the Function LED also is blinking red.**When the Function LED also is solid red.Camera Function LEDThe Axon Body 2 camera’s function LED displays when certain functions are enabled.Function Enabled Function LEDMute Blinking blueCamera error *** Solid redBluetooth feature is booting up Solid blue***Use the power switch to turn the camera off and on.Battery LEDThe camera’s battery LED displays the battery’s remaining capacity, when the deviceis being used or when charging.Battery Status Battery LEDBattery capacity is 41–100% GreenBattery capacity is 20–40% YellowBattery capacity is less than 20% Red during operation; flashing red andyellow during chargingBattery critically low Blinking red and yellowAxon Body 2 Quick Start GuideEnglishRecordingThe Axon Body 2 camera has two operating modes. The default mode, or BUFFERINGmode, provides pre-event buffering to capture activities that occur before you activatethe EVENT (recording) mode.1 Turn the system on. Move the ON/OFF switch to the ON position.• The camera takes a few seconds to boot up and be ready to record (the red areaunder the switch will be exposed with the switch moved to the ON position).• The operation LED will be solid red and then transition to blinking green whenthe system goes into BUFFERING mode.• The Axon Body 2 camera will go into BUFFERING mode after the boot upsequence. The BUFFERING mode holds the previous 30 seconds of video [NOAUDIO] leading up to the beginning of a recording.Solid RedBoot Up Mode Blinking GreenBUFFERING Mode2 To record, quickly double-press the EVENT button.• The camera now records audio as well as video.• The camera will beep twice to let you know that recording has started. The twobeeps will repeat every two minutes (audio notifications can be deactivatedif necessary).• The operation LED will blink red.3 To add a marker to the video, quickly press and release the Function button.4 To stop audio recording (mute), press and hold the Function button for threeseconds.5 To stop all recording and return to BUFFERING mode, press and hold the EVENTbutton for at least three seconds until there is a long, audible beep.With default settings, the system does not capture audio in BUFFERING mode, soanything recorded in that mode will be video-only. BUFFERING mode starts onlyafter the camera is turned on. The system does not record when the Axon Body 2camera is turned off.EVENT ButtonBlinking Red - EVENT ModeAxon Body 2 Wall Charger (not shown)HardwareAxon Body 2 USB CableAxon Body 2CameraRead, understand, and follow all current instructions, warnings, and relevant TASER training materials before using any Axon system. The most up-to-datewarnings and instructions are available at www.taser.com.Before using an Axon Body 2 camera, ensure it is fully charged, and connect it to Evidence.com via the Axon Dock or Evidence Sync software to ensure it isproperly configured. See Battery LED and Recharging the Battery and Uploading Data for more information. If the battery is removed or its charge is everdepleted, recharge and reconnect the camera again.Quick ReferenceUpload Status LEDBottom ViewCamera LensPower SwitchRed = On/BufferingRecharging/DataportData Transfer & Rechargingthrough PC or Axon DockTop ViewOperation LEDEVENT ButtonDouble Tap = Start RecordHold 3 Sec = Stop RecordSpeakerBattery LEDGreen = 41% - 100%Yellow = 20% - 40%Red = Less Than 20%Microphone Battery Status ButtonPush to Show Status ofBatteryFunction ButtonMute or add markerFunction LED |
Related manuals for Axon Body 2
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine