BARRON EXITRONIX 82 Series Manual

Contents

important safeguards

BARRON EXITRONIX 82 Series Manual Manual pdf 1 page image

82 SERIESLED LANE CONTROL SIGNSIMPORTANT SAFEGUARDSSAVE THESE INSTRUCTIONSDo not mount near gas or electric heaters.Equipment should be mounted in locations andat heights where it will not readily be subjectedto tampering by unauthorized personnel.The use of accessory equipment is notrecommended by the manufacturer and maycause an unsafe condition.Do not use equipment for other than intendeduse.WARNING: Installation andServicing should be performed byqualified service personnel only!WARRANTY5 YEAR LIMITEDEXITRONIX, a divsion of Barron Lighting Group,will replace or repair any components, which faildue to manufacturer’s defects or workmanship,for a period of 5 years. The warranty doesnot cover physical damage or abuse, andBarron Lighting Group reserves the right tocharge for such repairs if deemed necessary.SIGNS MUST BE CAULKED ACCORDING TOINSTALLATION INSTRUCTIONS IN ORDERFOR WARRANTY TO BE HONORED.7885 N Glen Harbor BlvdGlendale, AZ 85307Recessed-Mount Installation Instructions1. Use dimensions on back page to determine size ofopening needed to recess sign.2. Remove the four (4) screws from the sides of theEnclosure and remove the Backplate.3. Disconnect Transformer from LED Panel.4. Secure Flushmount Bezel to Enclosure using mountingholes located in Bezel tabs. CAUTION: Use care toavoid damaging internal components when drilling holesin Enclosure.5. Make electrical connections in accordance with localregulations (See Wiring Diagrams on back page) usingknockout provided in Backplate.6. Re-connect Transformer to LED Panel and secureEnclosure to Backplate using the four (4) screws.7. Secure recessed unit to exterior of wall using mountingholes provided on Bezel. Additional holes can be drilledinto Bezel if needed.8. USE A WATERPROOF CAULK TO SEAL THEFLUSHMOUNT BEZEL TO THE WALL.CANOPY CEILING MOUNTINGSCREWPLACEMENTFOR CEILIG MOUNTFIG BFIG A10070046 REV 5Enclosure Wall-Mount Instructions1. Turn off power to building supply wires before beginninginstallation.2. Remove the four (4) screws from the sides of theEnclosure and remove the Backplate.3. Disconnect Transformer from LED Panel.4. Mount Backplate directly to wall or junction box.5. Make electrical connections in accordance with localregulations (See Wiring Diagrams on back page) usingknockout provided in Backplate.6. Re-connect Transformer to LED Panel and secureEnclosure to Backplate using the four (4) screws.7. USE A WATERPROOF CAULK TO SEAL THE BACK OFTHE ENCLOSURE TO THE WALL.8. Make sure the two (2) 1/4” drain holes on the bottom ofthe Enclosure are not obstructed.Enclosure Ceiling-Mount Instructions (Fig A)1. Turn off power to building supply wires before beginninginstallation.2. Remove the four (4) screws from the sides of theEnclosure and remove the Backplate.3. Disconnect Transformer from LED Panel.IF USING OPTIONAL CANOPYPLEASE SKIP TO STEP A BELOW4. Mount Enclosure to ceiling, securing it with at least one(1) screw every six (6) inches along the middle of thetop of the Enclosure. (See Fig A).5. Make electrical connections in accordance with localregulations. (See Wiring Diagrams on back page.)6. Reconnect Transformer to LED Panel and secureEnclosure to Backplate using the four (4) screws.7. USE A WATERPROOF CAULK TO SEAL THE BACK OFTHE ENCLOSURE TO THE WALL.8. Make sure the two (2) 1/4” drain holes on the bottom ofthe Enclosure are not obstructed.Enclosure Canopy-Mount Instructions (Fig B)1. Turn off power to building supply wires before beginninginstallation.2. Mount Canopy to Enclosure.a. Drill (2) 3/16” holes for mounting screwsb. Drill (1) 7/8” hole for conduit3. Secure Mounting Plate to ceiling or junction box.4. Make electrical connections in accordance with localregulations. (See Wiring Diagrams on back page.)5. Secure Canopy/Enclosure assembly to Mounting Plateusing the four (4) screws provided.6. Reconnect Transformer to LED Panel and secureEnclosure to Backplate using the four (4) screws.7. USE A WATERPROOF CAULK TO SEAL THE CANOPYTO THE ENCLOSURE AND THE CEILING, ADN TOSEAL THE BACKPLATE TO THE ENCLOSURE.8. Make sure the two (2) 1/4” drain holes on the bottom ofthe Enclosure are not obstructed.

/ 2

Related manuals for BARRON EXITRONIX 82 Series