Balboa Water Group 500DZ Series Operation Manual

Also see for 500DZ Series: Operation guide Operation guide

Balboa Water Group 500DZ Series Operation Manual Manual pdf 1 page image

Warm Cool Mode/Prog Jets Blower LightTimehttp://www.balboawatergroup.com/Temp Control (80°F - 104°F / 26.0°C - 40.0°C)The last measured water temperature is constantly displayed.The water temperature displayed is current only when thepump has been running for at least 2 minutes.To display the set temperature, press “Warm” or “Cool” once. Tochange the set temp, press a temp button again before the displaystops flashing. After three seconds, the display will stop flashingand begin to display the current spa temperature.Jets 1Press “Jets 1” to turn pump 1 on or off, and to shift between lowand high speeds (if equipped). The low-speed will turn off after4 hours. High-speed will turn off after 15 minutes. Low-speedmay run automatically at times, during which it cannot bedeactivated from the panel, but high-speed may be operated.Jets 2/Jets 3/Blower (If equipped)Press the corresponding button once to turn the device on oroff. The device will turn off after 15 minutes. Pump 2 may betwo-speed on some systems.If the panel has a button with 2 devices assigned to it, like Pump2 and Pump 3, press the button repeatedly to step through thevarious combinations of On and Off for both devices.LightPress “Light” to operate the spa light. Turns off after 4 hours.Setting the Time of DayWhen the spa is first powered up, the words SET TIME will flashon the display. Press “Time,” then “Mode/Prog,” then “Warm” or“Cool.” The time will begin changing in one-minute increments.Press “Warm” or “Cool” to stop the time from changing. Press“Time” to confirm.Initial Start-upYour spa will enter Priming Mode ( ) when it is energized.During Priming Mode, press “Jets” button(s) repeatedly andbe sure all pumps are free of air. Priming Mode lasts less than5 minutes. Press “Warm” or “Cool” to exit. After Priming Mode,the spa will run in Standard Mode (see Mode/Prog section).Button shapes and labels may vary.Balboa 500DZ-Series Operation GuideThis document covers VS and GS systems 500DZ through 520DZ with Balboa Panels VL801D or VL802D.Mode/ProgMode is changed by pressing “Warm” or “Cool,” then pressing“Mode/Prog” button.Standard Mode maintains set temperature and the STANDARD iconwill be displayed.Economy Mode heats the spa to the set temperature only duringfilter cycles. will display when water temp is not current, andwill alternate with water temp when the pump is running. TheECONOMY icon will be displayed.Sleep Mode heats the spa to within 20°F/10°C of the settemperature only during filter cycles. will display when watertemp is not current, and will alternate with current water tempwhen the pump is running.Preset Filter CyclesThe first preset filter cycle starts at 8:00 AM and ends at10:00 AM. The second preset filter cycle starts at 8:00 PM andends at 10:00 PM.For non-circ systems, low-speed pump 1 and the ozone generator(if installed) run during filtration.For 24 hour circulation systems, the circ pump and the ozonegenerator (if installed) run 24 hours. In hot environments, thecirc pump may turn off for 30 minute periods, except duringfilter cycles.For non-24 hour circulation systems, the circ pump and ozonegenerator (if installed) run during filtration (and may also runautomatically at other times).At the beginning of each filter cycle all other equipment willrun briefly to purge the plumbing.Optional Filter Cycle ProgrammingYou are not required to change the filter cycles, but if you wishto, press “Time,” “Mode/Prog,” “Mode/Prog” within 3 seconds.SET START FILTER 1 (AM) will appear. Press “Warm” or “Cool” toreset the filter start time.Press “Mode/Prog” to see SET STOP FILTER 1 and adjust the timewith “Warm” or “Cool” as done above. Press “Mode/Prog” to seeSET START FILTER 2 (PM) and proceed as above. Press “Mode/Prog”to see SET STOP FILTER 2 and proceed as above. Press “Mode/Prog”to confirm.The pump responsible for heating and filtration (pump 1 low-speedon non-circ system, or the circ pump on circ systems) will bereferred to simply as the pump.In multi-button sequences, if the buttons are pressed too quickly inthe sequence, they may not register.SpaDepot.com

/ 2

Related manuals for Balboa Water Group 500DZ Series