Balboa Water Group 500SZ Series Operation Manual
  |
Warm Cool Mode Jets Blower Lightwww.balboawatergroup.comTemp Control (80°F - 104°F / 26.0°C - 40.0°C)The last measured water temperature is constantly displayed.The water temperature displayed is current only when thepump has been running for at least 2 minutes.To display the set temperature, press “Warm” or “Cool” once.To change the set temperature, press a temperature buttonagain before the display stops flashing. After three seconds,the display will stop flashing and begin to display the currentspa temperature.Jets 1Press “Jets 1” to turn pump 1 on or off, and to shift between lowand high speeds (if equipped). The low-speed will turn off after4 hours. High-speed will turn off after 15 minutes. Low-speedmay run automatically at times, during which it cannot bedeactivated from the panel, but high-speed may be operated.Jets 2/Jets 3/Blower (If equipped)Press the corresponding button once to turn the device on oroff. The device will turn off after 15 minutes. Pump 2 may betwo-speed on some systems.LightPress “Light” to operate the spa light. Turns off after 4 hours.Initial Start-upYour spa will enter Priming Mode ( ) when it is energized.During Priming Mode, press “Jets” button(s) repeatedly andbe sure all pumps are free of air. Priming Mode lasts for lessthan 5 minutes. Press “Warm” or “Cool” to exit. After PrimingMode, the spa will run in Standard Mode (see Mode section).Button shapes and labels may vary.Balboa 500SZ-Series Operation GuideThis document covers VS and GS systems 500SZ through 520SZ with Balboa Panels VL600S, VL700S, VL701S, or VL702S.ModeMode is changed by pressing “Warm” or “Cool,” thenpressing “Mode.”Standard Mode maintains set temperature. will be displayedmomentarily when you switch into Standard Mode.Economy Mode heats the spa to the set temperature only duringfilter cycles. will display when water temp is not current, andwill alternate with water temp when the pump is running.Sleep Mode heats the spa to within 20°F/10°C of the settemperature only during filter cycles. will display when watertemp is not current, and will alternate with water temp when thepump is running.Preset Filter CyclesThe first preset filter cycle begins 6 minutes after the spa isenergized. The second preset filter cycle begins 12 hours later.Filter duration is programmable for 2, 4, 6, or 8 hours or forcontinuous filtration (indicated by ). The default filter time is2 hours for non-circ systems and 4 hours for circ systems.To program, press “Warm” or “Cool,” then “Jets 1.” Press “Warm”or “Cool” to adjust. Press “Jets 1” to exit programming.For non-circ systems, low-speed pump 1 and the ozone generator(if installed) run during filtration.For 24 hour circulation systems, the circ pump and the ozonegenerator (if installed) run 24 hours. In hot environments, thecirc pump may turn off for 30 minute periods, except duringfilter cycles.For non-24 hour circulation systems, the circ pump and ozonegenerator (if installed) run during filtration (and may also runautomatically at other times).At the beginning of each filter cycle all other equipment willrun briefly to purge the plumbing.The pump responsible for heating and filtration (pump 1 low-speedon non-circ system, or the circ pump on circ systems) will bereferred to simply as the pump.In multi-button sequences, if the buttons are pressed too quickly insequence, they may not register.Automatic polling (in Standard Mode only)The pump will activate for 1 to 2 minutes to check the temperature:- every 30 minutes- whenever any other pump or blower is turned on- whenever the set temperature is raisedSpaDepot.com |
Related manuals for Balboa Water Group 500SZ Series
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine