Balluff BIS00W2 Installation Manual
    |
PIN 1:10~30VDCPIN 2:0VDC(PWR GND)PIN 3:N/CPIN 5:N/CPIN 6:RXPIN 7:TXPIN 8:SIGNAL GNDPIN 4:N/CN/C = Not Connected8-Pin, Male M12Interface Connector1. Attach the controller to the mounting bracket using the two sets of M4 screws, washersand nuts provided. Place the nuts in each of the hex-shaped recessed cavities at the rear ofthe Unit.2. Align the mounting bracket with the two mounting holes on the controller, then insert bothM4 screws (with washers) into the controller from the underside and secure completelyusing a standard Phillips #2 head screwdriver. Tighten screws to 0.7 Nm (6 lbs / inch)±10%.3. Fasten the other end of the mounting bracket to your work area. The Unit may be mountedhorizontally or vertically, but should be aligned in such a manner that the LED indicators canbe seen during operation.4. Connect the 8-pin, female M12 connector from your serial interface cable (CBL-1478) tothe 8-pin, male M12 connector on the Unit.5. Connect the 9-pin, female D-sub connector on the serial interface cable to a COM port onthe host computer. Tighten the cable’s two locking thumbscrews.6. Connect the 2.5 mm DC power plug on the power supply transformer to the DC powerjack receptacle on the serial interface cable. Tighten the locking ring to prevent power frombecoming disconnected during use. The Controller requires a power supply capable ofproviding 10~30 V DC, 2.4 W (100 mA @ 24 V DC).7. Plug the power supply transformer into a suitable AC power source. Apply power to thecontroller after all cable connections have been made. The LEDs on the unit will flash.8. On the host computer, set COM port parameters to: 9600 baud, 8 data bits, 1 stop bit,no parity and no handshaking.9. To verify operations, download the serial version of the HF Dashboard Utility. The HFDashboard Utility allows users to configure and control their controllers and send RFIDcommands for testing purposes.Figure 1: Controller, Mounting Bracket and Hardware4.5[0.18]2X28[1.10]57[2.25]2X7[0.27]92[3.63]3[0.13]42[1.65]SLOT5 X 16[.2 X .63]19[0.74]2XSLOT5 X 8[.2 X .31] 26[1.02]Millimeters[INCHES]Ř RFID devices can be negatively affected by the presence of metallic objects near its RF field.Avoid mounting the unit within 5 cm (two inches) of metallic surfaces.Ř Locate the unit away from sources of EMI (electro-magnetic interference) and away from devicesthat generate high ESD (electro-static discharge) levels.Ř Do not route the Unit’s cables near unshielded cables or near wiring that is carrying high voltage orhigh current (such as for motors or solenoids). Cross cables only at perpendicular intersections.Ř Use the included polycarbonate mounting bracket or a similar non-metallic bracket. The bracket isprovided to help reduce electrically conducted spurious noise by isolating the RFID controller frommetallic surfaces.Ř If multiple RFID controllers operating at the same frequency (13.56 MHz) are to be installed, maintaina minimum distance of 20 cm (8 inches) between adjacent RF devices.Figure 2: Dimensions56.2[2.21]28[1.10]HEX NUT RECESS7.2mm ACROSS FLATSØ4.5[Ø.18]MOUNTINGHOLE 2X40[1.57]Millimeters[Inches]24[0.94] 14.3[0.56] 12.5[0.49]39.2[1.54]15.5[0.61]Figure 3: Interface Connector - PinoutThe Balluff RFID Controller has one 8-pin, maleM12 connector that is used for data and power.BIS M-410-068-001-00-S115(C0405-232-01)Installation GuideInstalling the RFID ControllerInstallation GuidelinesŘ CBL-1478: Cable Assembly (8-pin, femaleM12 to RS232; with 2.5 mm DC powerjack, 2 m)Ř CBL-1488-XX: Cable (8-pin, female M12to bare wire leads)Ř CBL-1492-XX: Cable (8-pin, right-anglefemale M12 to bare wire leads)Ř CBL-1493: Connector (8-pos, straightfemale M12, field mountable)(XX = CABLE L ENGTH IN METERS )The Unit requires an electrical supplyvoltage of 10~30 V DC and has a powerdraw of 2.4 W (100 mA @ 24 V DC,1 Amp peak). Use a regulated powersupply that is capable of delivering theserequirements.Power RequirementsCabling Part Numbers890404B$$. (1.'; Subject to modification.5HSODFHVHGLWLRQwww.balluff.com |
Related manuals for Balluff BIS M-410-068-001-00-S115
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine