Cavius 9001-003 Manual
  |
Commercial reference: 9001-003Developed by CAVIUSPLEASE READ THE USER GUIDEC A R E F U L LY B E F O R E U S E A N DRETAIN FOR FUTURE USE!General description:The Smart Remote is designed to alert with a rapidflashing warning light when alarming and to remotelycontrol the CAVIUS Wireless Alarm Family. The torchfunction can be used to find escape routes at night.Technical information:The Smart Remote can be used with the alarms fromthe CAVIUS Wireless Alarm Family: Smoke, Heat,Flood, CO and Mains Power alarms. The maximumnumber of alarms that can be interlinked with is 32.The minimum range is 100m in open field. RF conditionsalso depend on the house layout and materials. You shouldalways test it after installation and after changing bat-teries.Diameter: 27mm Length: 140mmThe Smart Remote is powered by 3 replaceable DURA-CELL AAA Alkaline batteries. Please note that correctoperation of the Smart Remote device is ensured by useof DURACELL batteries.Interlinked by RF: 868 MHz.Complies to standards: RoHS, REACH, R&TTE,EN60065, EN300-220.How to connect to the Wireless Alarm Family:1. Open the battery compartment by pressing the snap.Insert the batteries in the battery compartment respectingpolarities.2. Slide the learn switch to the “Learn mode” position.The Smart Remote will go into Learn mode.All alarms that need to be connected to the SmartRemote in the house should be put into “Learn mode”by sliding the switch of each device on the “Learn mode”position.3. The flashlight will light up to indicate that “Learnmode” has been selected.Please note: Do not take out the batteries during “Learnmode” as this will interrupt the learn process.4. Press and hold the test button of the Smart Remoteonly, until it beeps and the flashlight flashes. It willbecome the master and will start sending out a specifichouse code to the other alarms.5. As the other alarms receive the specific house code,they will also start flashing their red LED’s.6. When all alarms flash the red LED, they are connectedand can be switched out of “Learn mode” and installed.Installation:The body of the Smart Remote has a built-in magnet, so itcan be installed on a metal plate mounted on the wall,or on a fridge or other metal surfaces.The accompanying metal plate can be installed by thedouble sided tape or the enclosed screw set.The end cap has a hole in which a lanyard can be addedso the remote can hang from a hook etc.Test of alarms:After installation, and at least once per quarter, test allyour alarms by pressing the test button on the remote toensure they are operating correctly and are within rangeof each other.It is recommended to check visually every week if theLED flashes correctly on the alarm (every 48sec.).The Smart Remote can activate the RF test function ofthe alarms by sending out the a test signal by press-ing the button at the end for two sound sweeps ofalarm signal 1 (--- --- ---) for about 7 sec. The SmartRemote will flash/beep every 8 seconds for 120 secondsto indicate that the test signal is being transmitted.If the Smart Remote is receiving a test signal fromanother device, it will flash/beep every 8 seconds for120 seconds to indicate that it is part of the group.Indication can be stopped by pressing the end button.Please note: To ensure an optimal operation in normalconditions, test function sends out a reduced power RFsignal.Alarm mode:When one of the connected alarms is going into alarmand sending out the RF alarm signal, the Smart Remote’sflashlight will start flashing rapidly (stroboscope).The Smart Remote also has a built in vibrator which willfollow the sound pattern of the sounder. During alarm thevibrator will vibrate.The torch can be switched from stroboscopic flashing toconstant on by pressing the side button.Please note: Flashlight will flash at 2 Hertz (2 timeseach second) to avoid photo sensitive epilepsy tobe triggered.The CAVIUS Wireless Family has two different alarmsignals:Alarm signal 1 (--- --- ---) is life threatening alarms, likea smoke alarm.Alarm signal 2 (- - -) is a non life threatening alarm, likea flooding alarm:Smoke alarm signal: --- --- ---Heat alarm signal: --- --- ---Flood alarm signal: - - -CO alarm low level signal: - - -CO alarm high level signal: --- --- ---Please note that only the originating alarm’s LED willflash, so it can be identified.Alarm silence:When the alarms from the Wireless Alarm Family gointo alarm, they can be silenced by pressing end buttonof the Smart Remote.Please note: Due to coming legislation, the hush signalis transmitted with reduced power (the remote mustbe within short range from the silenced alarm, whichmeans you should be in the same room as the alarm).UKFlashlightEnd cap for battery accessEnd button for test/hushMagnet holderLearn mode switchSide button for flashlightNormal Mode Learn Mode |
Related manuals for Cavius 9001-003
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine