867Additional InstructionsPuller Feed Drive

About this additional manual

machine overview

Operation

Setting the top puller pressure

Settings

Setting the puller feed operating mode

Service

Setting puller feed operation

Appendix

Dürkopp Adler 867 Additional Instructions

Scope of Delivery

Assembling the stand components (Long arm)

Setting the working height

Drive category, type and use

Fitting the sewing drive

Fitting the sewing-drive control for machines with direct drive (only 867-190142-M)

Fitting the pedal

Fitting the machine head

Fitting and tensioning the V-belt

Attaching the knee lever

Fitting the operating panel

General

Earthing

Connecting the sewing drive to the mains

Fitting the proximity switch

Direction of rotation of sewing drive

Connecting the sewing light transformer (optional equipment)

Connection to the DA321G

Connection to the DAC Classic

Connecting the direct drive

Connecting the DA321G control unit

Connecting the knee switch

Mounting the M-Control PCB

Setting the switches on the M-Control PCB

Setting machine-specific parameters

Lubrication

Sewing test

allgemeine information

general information

general safety instructions

technical data

service instructions

Gauges

Description of the locking positions

Graduation on the handwheel

Position of the arm shaft crank on the arm shaft

Upper and lower toothed belt wheel / toothed belt

Position of the lower toothed belt wheel

Bottom feed and stitch regulator gear

Adjust the 2nd stitch length

Position of the feed dog in the throat plate cutout

Feed dog height

Balance weight

Transmission lever

Needle bar linkage

Needle penetration in feeding direction

Hook, looping stroke and needle bar height

Needle bar height

Distance between hook and needle

Needle guard

Bobbin case opening

Timing of opening

Feeding foot and presser foot stroke

Stroke motion of the feeding foot

Sewing foot pressure

Stitch length limitation

Stitch equality of the forward and backward stitch

Sewing foot lifting

Height of the sewing feet arrested with hand lever

Height of the lifted sewing feet

Thread-guiding parts

Thread take-up spring

Bobbin winder

Thread trimmer

Thread pulling knife

Counter-knife and lower thread clamp

Cutting position with machines having needle repositioning

Cutting position with machines without needle repositioning

Potentiometer in the arm

Basic setting with the control panel V810 or V820

Check the potentiometer adjustment

Oil lubrication

Hook lubrication

Maintenance

About these instructions

Safety

Signal words and symbols used in warnings

Working basis

Removing the covers

Removing and fitting the arm cover

Removing and fitting the head cover

Opening and closing the throat plate slide

Removing and installing the throat plate

Removing and installing the feed-dog

Surfaces on shafts

Putting the handwheel into position

Setting the handwheel scale

Positioning the arm shaft

Positioning the toothed belt wheels

Upper toothed belt wheel

Lower toothed belt wheel

Setting the stitch length adjusting wheels

Setting the upper stitch length adjusting wheel

Setting the lower stitch length adjusting wheel

Setting the stitch length limit

Setting the eccentric for the forward and backward stitches

Setting the feed-dog

Moving the feed-dog

Moving the feed-dog carrier

Setting the feed-dog movement

Setting the feed-dog height in the top dead center

Feed dog stroke (default)

Setting the compensating weight

Feed dog stroke (adjustable stroke eccentric)

Setting the stroke eccentric

Aligning the needle bar linkage

Aligning the needle bar linkage in the sewing direction

Position of the hook and needle

Setting the loop stroke position

Adjusting the needle guard

Setting the needle bar height

Setting the spool housing lifter

Setting the lifting gap

Setting the point in time of opening

Sewing feet

Setting an even sewing foot stroke

Setting the stroke movement for the feeding foot

Setting presser foot pressure

Setting the sewing foot lifting height

Setting needle thread tension

Setting the thread tensioning spring

Winder

Setting the winder

Setting the hook thread guide

Thread cutter

Setting the cutoff curve

Setting the cutting pressure

Adjusting the needle thread tension

Short thread cutter (KFA)

Setting the locking latch

Setting the thread-pulling knife

Setting the counter-blade

Setting the cutoff position

Setting the potentiometer

Setting the safety snap-on coupling

Setting the torque

Machines with integrated motor

Disassembling the drive

Assembling the drive

Replacing the fuse

Replacing the PCB

Special machines

Adjusting the slide for the needle bars

Machines with moving binder

Machines with a vertical cutter

Activating the tensioner lift

Maintenance work

Lubrication of the upper part of the machine

Pneumatic system

Draining the water condensation

Cleaning the filter element

Cleaning work

Clean the motor fan sieve

Checking the toothed belt

Decommissioning

Disposal


Contents Table Of Contents About this additional manual machine overview Operation Setting the top puller pressure Settings Setting the puller feed operating mode Service Setting puller feed operation Appendix	867Additional InstructionsPuller Feed Drive Next / 18