D2D 3102 Quick Reference Install Manual
  |
© 2013 Directed. All rights Reserved.1Quick Reference Install GuideVehicle Security SystemModel 3102DetailLEDAntennaSensor 2Sensor 3Valet Switch998T Bitwriter/SmartStartParking LightFlash JumperDomelight SupervisionOutput (pin #87 of onboardrelay): Connect to (-) groundif the domelight circuit isnegative or to +12V if thedomelight circuit is positive.Pin #87A of OnboardDoor Lock Relay:This wire is typicallyused whenever the doorlock switch needs isola-tion.Pin #30 of OnboardDoor Lock Relay:Connect to the doorlock wire in the vehicle.Pin #87 of OnboardDoor Lock Relay:Connect to (-) ground ifthe locks are negativeor to +12V if the locksare positive.Pin #87A of OnboardDoor Unlock Relay:This wire is typicallyused whenever the doorlock switch needs isola-tion.Pin #30 of OnboardDoor Unlock Relay:Connect to the door un-lock wire in the vehicle.Pin #87 of OnboardDoor Unlock Relay:Connect to (-) ground ifthe locks are negativeor to +12V if the locksare positive.Red/White (-) 200mA Trunk Release OutputLt. Brown (-) 200mA Horn Honk OutputViolet/Black (-) 200mA Aux 2 OutputLt. Green/BlackWhite/Black (-) 200mA Aux 3 OutputGray/Black (-) 200mA Aux 4 OutputOrange/Black (-) 200mA Retained Acc OutputGray (-) Hood Trigger InputLt. Blue (-) 200mA 2nd Unlock Output(-) 200mA OEM AlarmDisarm OutputRed (+) 12V Constant Power InputBrown (+) Siren OutputYellow (+) Switched Ignition InputBlack (-) Chassis Ground InputViolet (+) Door Trigger InputViolet (87) of onboard Unlock RelayBlue/Black (30) of onboard Unlock RelayBrown/Black (87A) of onboard Unlock RelayViolet/Black (87) of onboard Lock RelayGreen/Black (30) of onboard Lock RelayWhite/Black (87A) of onboard Lock RelayBlue (-) Instant Trigger InputGreen (-) Door Trigger InputGreen/BlackGreenGreen/WhiteBlack/White (30) of onboard Domelight Sprvsn RelayBlack/White (87) of onboard Domelight Sprvsn RelayWhite/Blue (-) 200mA Aux 1 OutputWhite (+ or -) Selectable Light Flash OutputOrange (-) 500mA GWA OutputWiring ConnectionsTrunk Release Output: Connect to thevehicle negative (-) trunk release relay orother low current device. NEVER connectdirectly to a motor or high current devicewithout a relay.12V Constant Power Input: Remove theinline fuse before connecting to a wirethat has (+) 12V at all times. Reinstall theinline fuse when wiring connections arecomplete.Siren Output: Connect to the (+) wire onthe siren.+12V Ignition Input: Connect to a wirethat has (+) 12V while the key is in therun and crank positions.Chassis Ground Input: Connect to ascraped (bare) metal surface in the driverkick panel. NEVER connect to dashbrackets or to a factory ground.Door Trigger Input:Green: Connect to a wire that rests at (+)12V when all doors are closed and (-)ground when any door is opened.ORViolet: Connect to a wire that rests atground when all doors are closed and(+) 12V when any door is opened.Instant Trigger Input: Connect to a wirein the vehicle that goes to ground whenopened (typically the trunk) or to an op-tional Directed single zone sensor.Domelight Supervision Output (pin #30of onboard relay): Connect to a wire thatturns on the domelight to illuminate thevehicle interior when disarming and turn-ing off the ignitionAux 1 Output: Connect to an auxiliaryconvenience or expansion option. NEV-ER connect directly to a motor or high cur-rent device without a relay.(+ or -) Light Flash Output: Connect tothe vehicle parking light wire. Select thecorrect polarity with the output or vehicledamage may occur.Ground When Armed Output: Connectto a starter interrupt relay or an accessorythat requires a ground to activate whenthe system is armed.Important: NEVER connect 200mA low current outputsdirectly to a motor or high current device WITHOUTa relay,OEM Alarm Disarm: Connect to thefactory alarm disarm wire in the ve-hicle (if applicable). NEVER connectdirectly to a motor or high current de-vice without a relay.Horn Output: Connect to the vehicles(-) horn honk relay wire.Aux 2 Output: Connect to an auxilia-ry convenience or expansion option.NEVER connect directly to a motor orhigh current device without a relay.Aux 3 Output: Connect to an auxilia-ry convenience or expansion option.NEVER connect directly to a motor orhigh current device without a relay.Aux 4 Output: Connect to an auxilia-ry convenience or expansion option.NEVER connect directly to a motor orhigh current device without a relay.Retained Acc Output: Connect to arelay that controls the accessory cir-cuit in the vehicle.Hood Trigger Input: Connect to awire that goes to ground when thehood is opened.2nd Unlock Output: Connect to awire (or relay assembly) that unlocksall doors when installing two stagedoor unlocking.(87A) Normally Closed: To car side ofstarter wire if programmed as a Nor-mally Closed circuit (factory default).(87) Normally Open: To car side ofstarter wire if programmed as a Nor-mally Open circuit.(30) Common: To key side of starterwire.Remote control configuration4- button remote control configurationFeature DescriptionA U XArm: Lock the doors and arm the vehicleDisarm: Unlock the doors and disarm the vehicleAUX Trunk Release/Silent Mode: Activate Silent Modeand Auxiliary functionsAUXPanicA U XandA U XAux 1: Press together to control an Auxiliary outputProgramming System FeaturesThe System Features Learn Routine dictates how the unit operates. It is possible toaccess and change most of the feature settings using the Valet switch.1. Open a door.2. Turn the ignition on, then off.3. Select a Menu. Press and hold the Valet switch. The number of siren chirpsindicates the menu number. 1 chirp indicates menu 1, 2 chirps - menu 2, and3 chirps for menu 3.4. When the desired menu chirps are heard, release the Valet switch.5. Select a Feature. Press and release the Valet switch the number of times cor-responding to the feature you wish to change. Then press and hold one moretime to select the features.6. Program the Feature. While holding the Valet switch, you can program thefeature using the remote control.To change the desired options press;AUX= one chirp setting, whileAUX= two,three or higher chirps setting.Once a feature is programmed:• Other features can be programmed within the same menu• Another menu can be selected• The learn routine can be exited if programming is completeTo access another feature in the same menu:1. Press and release the Valet switch the number of times necessary to advancefrom the feature you just programmed to the next one you want to program.2. Then press the Valet switch once more and hold it.To select another menu:1. Press and hold the Valet switch.2. After 3 seconds, the unit advances to the next menu and the siren chirps, indi-cating which menu has been accessed.The learn routine exits if any of the following occurs:• The open door is closed• The ignition is turned On• There is no activity for 15 seconds or more• The Valet switch is pressed too many timesProgramming continued on page 2.A U XBitwriters with a date code of 6a or older require an ICupgrade (p/n 998M). Some bitwriters with a date codeof 6B do not require the IC upgrade, refer to tech tip #1112 for more information.The Bitwriter® (p/n 998U)requires chip version 2.4 ornewer to program this unit.Note: For more door lock wiring information, see tech tip #1041 at: www.directechs.com (authorized users only).Note: The sensor ground outputs from the systemare only active when the system is armed. |
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine