Daktronics Sportsound SSR-200 Installation Instructions Manual

Also see for Sportsound SSR-200: Quick start guide Operation manual Quick start guide

Daktronics Sportsound SSR-200 Installation Instructions Manual Manual pdf 1 page image

Sportsound SSR-200 Installation & Commission Work InstructionsPage 1 of 2DD2298507Rev 0301 April 2019201 Daktronics DriveBrookings, SD 57006-5128www.daktronics.com/support800.325.8766Task (Major Step) Process / Key Points / Reason Why (if applicable) Tools Required / Reference MaterialsTHESE ARE FIELD SERVICE INSTALLATION INSTRUCTIONS. REFER TO SUBCONTRACTOR SCOPE OF WORK FOR THEIR RESPONSIBILITIES.1. Receive EquipmentF Unload equipment from truckF Store control equipment in secure locationa. Receive equipment.b. Store all front-end control equipment in a secure locationor press box to prevent damage or theft. Control systemshould not be left in an outdoor environment.• Video Playlist: SSR-200 Control System• SSR-200 Gen II Operation Manual(DD3159816)This manual includes all drawingsreferenced below.2. Inspect EquipmentF Inspect rack equipment for damageF Report damage to PMa. Visually inspect the rack equipment for deep scratches,dents, chips, etc.b. Contact PM/PC about any damaged goods.3. Set up Control SystemF Remove front, top, and back coversF Set antennas at 45° anglesF Connect Announcer’s Interface to rackF Connect microphone and headphonesF Plug in power for announcer’s interfacea. Remove front, top, and back covers from the rack.b. With optional wireless receiver(s) installed, positionantennas outward at 45° angles as shown in image 3b.Optional In-Ear Monitor antenna points straight up.Optional ADA Hearing Assist antenna is wall mounted;mount and connect based on manufacturer’srecommendation (within 25' of control rack).c. Connect interface cable between announcer’sinterface and MIC 1 and AUX 1 on side of rack.d. Set up wired microphone w/ stand and plug intoannouncer’s interface MIC 1 INPUT jack. Plugheadphones or headset into 1/4" jack.e. Power announcer’s interface with provided powersupply. Use the outlets in the rack if possible.• Section 3 of Operation Manual• SSR-200 Gen II Quick Start Guide(DD3159573)4. Plug in and Turn on RackF Connect rack to powerF Connect rack to sound system inputF Turn on power to the rackF Turn AUDIO SIGNAL switch to ONa. Plug control system into a power receptacle.Power for the control rack (and fiber box) shall NOT beon the same circuit as the All Sport console.b. Route the XLR cable from AUDIO OUT on the side of therack to a wall plate (or fiber conversion box).c. Switch the power strip to the ON position.d. Switch the AUDIO SIGNAL to ON.• Section 3 of Operation Manual• SSR-200 Gen II Quick Start Guide(DD3159573)5. Inspect All Source Equipment LEDsF Verify mixer POWER LED is onF Verify Announcer’s Interface POWER LED isonF Verify wireless receiver(s) powered onF Verify CD player is onF Verify optional Hearing Assist System is onF Verify optional In-Ear Monitor System is ona. Verify mixer POWER LED is on.b. Verify Announcer’s Interface POWER LED is on.c. Verify one or both wireless receivers (if present) arepowered on.*d. Verify CD player is on.*e. Verify optional Hearing Assist power is on.*f. Verify optional In-Ear Monitor power is on.**LCDs display text when powered on.6. Test Mixer & I/O PanelF Connect music source into input 2F Set channel gainF Turn up channel faderF Turn up maser faderF Repeat testing for other inputsF Reset controls back to original settingsa. Connect the LTIBLOX device between input 2 on themixer and a laptop/smartphone, and then play anappropriate song.b. Verify PFL is enabled only on channel 2, use the GAINknob to set channel gain, and then turn off PFL.c. Turn up channel fader to desired level.d. Turn up master fader to desired level.e. Repeat testing for other inputs.f. Set controls back to original settings unless they were setimproperly.• Section 3 of Operation Manual• SSR-200 Gen II Quick Start Guide(DD3159573)5a. Mixer Power3b. SSR-200 Rack 3c. Interface Cable5b. Announcer’sInterface Power5c. Wireless MicPowerProducts Involved:SSR-2003c & 4b. ConnectionsAnnouncer’sInterface (Gen II)Side ViewORFiber Box(outdoor) Wall Plate(indoor)

/ 2

Related manuals for Daktronics Sportsound SSR-200