Dancing Wings Hobby S23 1.2M Piper J3 Cub Instruction Manual

Contents

instruction manual

Dancing Wings Hobby S23 1.2M Piper J3 Cub Instruction Manual Manual pdf 1 page image

机身组装Assemble the Fuselage工具 Tools NeededS23 1.2M Piper J3 CubInstruction Manual散件 KIT1234机翼，尾翼组装Assemble the Wing and Tail尾翼组装Assemble the Tail13机翼组装Assemble the Wing16机翼前缘Leading edge of the wing粘贴机翼前缘L3并按机翼弧度打磨成弧形水平尾翼和垂直尾翼在机身尾部调整好后，用胶水粘合固定。调整好头罩位置后，用自攻螺丝固定头罩到机身上。此处磁铁安装时与C6处磁铁为相吸状态。When the magnet is installed, it is ina state of attraction with the magnetat C6.After adjusting the position of thecowling, fix the cowling to thebody with self-tapping screws.The leading edge of the wingis polished to an arc accordingto the curvature of the wing.After the horizontal tail and thevertical tail are adjusted at the rear ofthe fuselage,they are glued and fixed.C1C1-2C1-1C2F14F1*2F2F3C4F11 F11F10F5F4F6 F7 F8 F9 F13第一步拼装侧板，C1，C1-1，C1-2按图示粘贴在一起，粘贴时保持平整，左右2片相同拼装。The first step is to assemble the sidepanels. C1, C1-1, and C1-2 are pastedtogether as shown in the figure. Theyare kept flat when pasted, and thetwo pieces at left and right areassembled in the same way.PVC片粘在侧板和C2中间，粘之前撕掉保护膜。The PVC sheet is stuck inthe middle of the sideplate and C2, and theprotective film is peeledoff before sticking.拼装另一边侧板，并在图示位置嵌入3x3mm轻木条，胶水固定。Assemble the otherside panel andembed the 3x3mmbalsa wood strip inthe position aspicture shown,finallyglue it.F13-1打磨成机身一体的弧度后再粘贴到尾部。F13-1 is polished into thearc of the fuselage andthen pasted to the tail.机翼组装参照机翼1：1图纸进行，并在平整工作台上进行组装，保持机翼平直。The wing is assembled as per the 1:1drawing,and assembled on the leveling tableto keep the wing straight.撕掉保护膜Remove theprotective film爪牙螺母Claw nutIn the middle中间对齐Align3C6F1256 789F15F13R2-1M1C5C5-113F13-1C3-1背面backC7C3对齐101112141517W5L1W8WM2W7W2-118底面 Bottom顶部 Top翻转Turn over1920L3头罩组装Cowling Installation自攻螺丝Self-tapping screws自攻螺丝Self-tapping screws磁铁 Magnet磁铁R1E1E2MagnetAlign此处按实际长度截取Cut here by actual length3X3mm轻木Balsawood3X3mm轻木Balsawood

/ 2

Related manuals for Dancing Wings Hobby S23 1.2M Piper J3 Cub