Datalogic 11-0139 Installation, Assembly And Operation Manual
  |
Datalogic USA, Inc.959 Terry Street | Eugene, OR 97402 | U.S.A.Telephone: (541) 683-5700 | Fax: (541) 345-7140©2012-2021 Datalogic S.p.A. and/or its affiliatesAll rights reserved. Without limiting the rights under copyright, no part of thisdocumentation may be reproduced, stored in or introduced into a retrieval sys-tem, or transmitted in any form or by any means, or for any purpose, without theexpress written permission of Datalogic S.p.A. and/or its affiliates.Owners of Datalogic products are hereby granted a non-exclusive, revocablelicense to reproduce and transmit this documentation for the purchaser's owninternal business purposes. Purchaser shall not remove or alter any proprietarynotices, including copyright notices, contained in this documentation and shallensure that all notices appear on any reproductions of the documentation.Electronic versions of this document may be downloaded from the Datalogicwebsite (www.datalogic.com). If you visit our website and would like to makecomments or suggestions about this or other Datalogic publications, please letus know via the "Contact" page.DisclaimerDatalogic has taken reasonable measures to provide information in this manualthat is complete and accurate, however, Datalogic shall not be liable for technicalor editorial errors or omissions contained herein, nor for incidental or conse-quential damages resulting from the use of this material. Datalogic reserves theright to change any specification at any time without prior notice.TrademarksDatalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. inmany countries, including the U.S.A. and the E.U.PowerScan is a trademark of Datalogic S.p.A. and/or its affiliates, registered inthe U.S. All other brand and product names may be trademarks of their respectiveowners.PatentsThis product is covered by the following patent.5,508,505.WEEE STATEMENTEnglishFor information about the disposal of Waste Electrical and ElectronicEquipment (WEEE), please refer to the website at www.datalogic.com.ItalianPer informazioni sullo smaltimento delle apparecchiature elettriche edelettroniche consultare il sito Web www.datalogic.com.FrenchPour toute information relative à l’élimination des déchets électroniques(WEEE), veuillez consulter le site internet www.datalogic.com.GermanInformationen zur Entsorgung von Elektro- und Elektronik- Altgeräten(WEEE) erhalten Sie auf der Webseite www.datalogic.com.SpanishSi desea información acerca de los procedimientos para el desecho de losresiduos del equipo eléctrico y electrónico (WEEE), visite la página Webwww.datalogic.com.PortuguesePara informações sobre a disposição de Sucatagem de EquipamentosElétricos e Eletrônicos (WEEE -Waste Electrical and ElectronicEquipment), consultar o site web www.datalogic.com.Chinese有关处理废弃电气电子设备 (WEEE) 的信息， 请参考 Datalogic 公司的网站 www.datalogic.com。Japanese廃電気電子機器 (WEEE) の処理についての関連事項は Datalogic のサイトwww.datalogic.com をご参照下さい。Waste Electrical and Electronic Equipment (WEEE)StatementPowerScan™Heated HolderINSTRUCTIONS SHEET820118301 Rev. B July 2021©2012-2021 Datalogic S.p.A. and/or its affiliates • All rights reserved• Without limiting the rights under copyright, no part of this docu-mentation may be reproduced, stored in or introduced into a retrievalsystem, or transmitted in any form or by any means, or for any pur-pose, without the express written permission of Datalogic S.p.A. and/or its affiliates • Datalogic and the Datalogic logo are registeredtrademarks of Datalogic S.p.A. in many countries, including the U.S.and the E.U.www.datalogic.comInstallation, Assembly, and OperationINSTALLATION1. Attach the bracket to your forklift using 1/4 inch (6.35mm) diameter screws and lock washers (not provided).2. Connect the Heated Holder power cable to your forklift battery as follows:• Strip the holder BLACK (negative) wire and connect it to the negative battery terminal or to the chassis of the lift. Use a properfastener to ensure good electrical contact, such as a wire terminal (not provided).• Strip the holder RED (positive) wire and connect it to the ignition switch of the forklift. Use a proper fastener to ensure goodelectrical contact, such as a wire terminal (not provided). If this connection is made directly to the battery’s positive terminal,provide an inline switch so it can be turned off when not in use. If you use an inline switch, make sure that its current and volt-age ratings are sufficient. See the Specifications on the following page for the three models.Refer to your forklift owner’s manual, or contact your supplier or electrician for additional information or instructions.• The Heated Holder is reverse-polarity-protected and will not function if connected backwards.• Secure any excess cable slack to the forklift at one-foot intervals.ASSEMBLYAssemble the bracket to the Heated Holder housing with the four mounting screws (see Figure 1). Depending on installation require-ments, you can mount the bracket as shown, vertically above the Heated Holder, or on the opposite side. Ensure that the Heated Holderis mounted with the front brushes towards the operator, and bottom brushes downward.Figure 1 - Heated Holder Mounting DiagramCAUTION: Ensure installation is performed by qualified service personnelDANGER: Exercise extreme caution when you are working with the forklift battery. If handled improperly, the currentfrom the DC battery can cause injury or death.CAUTION: The Heated Holder is intended for direct-current (DC) connection only. Do not connect to a “line” or AC voltagesource. |
Related manuals for Datalogic 11-0138
manualsdatabase
Your AI-powered manual search engine