Gryphon™ I GM410XGeneral Purpose HandheldLinear Imager Barcode Readerwith Datalogic’s STAR Cordless System™Quick Reference Guide

Datalogic Gryphon I GM4100-BK Quick Reference Manual

INTRODUCTION

Manual Conventions

About the Reader

Base Button

Display

battery safety

Programming the Reader

SETUP

Installing the Interface Cable

Configuring the Base Station

Changing the Base Station Position

Connecting the Base Station

Connecting the Base when Security Pin is Enabled

linking a bt reader to a pc

Stand Alone Layouts

Interface Selection

Customizing Configuration Settings

Resetting the Product Configuration to Defaults

Replacing the Battery

CONFIGURATION USING BARCODES

Reading Configuration Barcodes

GLOBAL INTERFACE FEATURES

RS-232 ONLY Interface

Baud Rate

Data Bits

Parity

Handshaking Control

RS-232/USB-Com Interfaces

Intercharacter Delay

beep on not on file

ACK NAK Options

ACK Character

ACK NAK Timeout Value

ACK NAK Error Handling

Disable Character

Keyboard Interface

Country Mode

Caps Lock State

Numlock

Send Control Characters

Wedge Quiet Interval

Intercode Delay

USB Keyboard Speed

USB Keyboard Numeric Keypad

USB-OEM Interface

USB-OEM Device Usage

IBM 46XX Interface

xx Number of Host Resets

Transmit Labels in Code 39 Format

Wand Emulation Interface

Wand Signal Speed

Wand Idle State

Label Symbology Conversion

Data Format

Global Prefix/Suffix

Global AIM ID

GS1-128 AIM ID

Label ID

Label ID Control

Label ID Symbology Selection

Set Global Mid Label ID Characters

Case Conversion

Reading Parameters

Double Read Timeout

Label Gone Timeout

Sleep Mode Timeout

LED AND BEEPER INDICATORS

Good Read Beep Type

Good Read Beep Length

Good Read Beep Volume

Good Read LED Duration

SCANNING FEATURES

Stand Mode Triggered Timeout

Stand Detection

Stand Mode Sensitivity

Flash On Time

Green Spot Duration

Code Selection

DISABLE ALL SYMBOLOGIES

CODE EAN/UPC

UPC-A

Expand UPC-A to EAN-13

UPC-A Minimum Reads

UPC-E

Expand UPC-E to EAN-13

UPC-E Number System Character Transmission

GTIN FORMATTING

EAN 13 Enable/Disable

EAN-13 Flag 1 Character

EAN 13 Minimum Reads

Gryphon I GM4100 guide

The BC40xx™ Radio Base

BC40XX UV Counterfeit Detection

Battery Safety

Linking the Reader to a Base Station

GRYPHON™ I System and Network Layouts

ISSN

Introduction

Technical Support

Getting Started

Install the Batteries

Install the Interface Cable

Connect the Base Station

Using the BC40xx™ Radio Base

Select the Interface Type

Configure Other Features

General Features

LED and Beeper Indicators

Good Read: When to Indicate

Good Read Beep Frequency

Scanning Features

Scanning Active Time

Flash Off Time

Contrast

Backlight

Display Mode

Display Timeout

Keypad Select

Interfaces

Global Interface Features

USB Suspend Mode

Beep On ASCII BEL

NAK Character

ACK NAK Retry Count

Indicate Transmission Failure

Enable Character

Interface Options

Wand Polarity

Transmit Noise

Data Editing

Please Keep In Mind

Label ID: Set Individually Per Symbology

Character Conversion

RF Features

RF Beeper Features

Beep Frequency

Beep Duration

Beep Volume

Disconnect Beep

Leash Alarm

end user license agreement

Software Product Policy

Securing the DC Power Cord (Optional)

Charging the Batteries

Replacing the Batteries

Link Datalogic RF Devices to Base

System and Network Layout

Selecting the Interface Type

Scancode Tables

Programming

Technical Specifications

LED and Beeper Indications

programming mode

Error Codes

Base Station Indications

Statement of Agency Compliance

FCC RF Radiation Exposure Statement

Imager Labeling

WEEE Statement

Warranty

Ergonomic Recommendations

Services and Support

declaration of conformity

Canadian Notice

Setting Up the Reader

wand emulation

Gryphon I GM4100-BK

Gryphon I GM410X