Datalogic S3Z LASER Series Instruction Manual

Datalogic S3Z LASER Series Instruction Manual Manual pdf 1 page image

Bracket(option)ScrewsM3x12S3Z LASER SERIESINSTRUCTION MANUALCONTROLSOUTPUT LEDThe yellow LED indicates the output status.STABILITY LED (S3Z…B01/F01)The green LED ON indicates that the received signal has a safetymargin greater than 20% compared to the output switching value.POWER ON LED (S3Z…G00)The green LED indicates that the sensor is operating.TRIMMER (S3Z…B01/F01)The trimmer can be used to adjust sensitivity; the operatingdistance increases turning the trimmer clockwise.ADJUSTMENT SCREW (S3Z…M01)This control can be used to adjust the cutoff distance (6 turnsscrew); the operating distance increases turning the controlclockwise.LIGHT/DARK TRIMMERThis switch can be used to set light or dark operation mode.WARNING (only for S3Z…B01/F01):The trimmer rotation is limited to 250° by a mechanical stop.Do not apply excessive torque when adjusting (max 0.05 Nm).INSTALLATION- Do not apply excessive impact onthe sensor during the installationprocess, so as to prevent damageor deterioration in the degree ofprotection.- To install the sensor, tighten themounting screws to a torque of0.5 Nm or less.- Install the Backgroundsuppression type sensor headperpendicular to the objecttransfer as shown below to minimize sensing errors.CONNECTIONSThe connections are compliant to the EN 60947-5-2 standard.S3Z…B01/F01/M01+BROWNBLACK1410…30 VDCBLUE 3 0 VOUTPUTS3Z…G00+BROWN 110…30 VDCBLUE 3 0 VM8 CONNECTOR2143TECHNICAL DATAS3Z…B01 S3Z…F01/G00 S3Z…M01Power supply: 12 … 24 VDC (operating limit 10…30VDC); (Class 2 UL508) reverse polarity protectedRipple: p-p 10% max.Current consumption(output current excluded): 35mA max. 30mA max. mod.F0115mA max. mod.G00 35mA max.Output: LIGHT or DARK; PNP or NPN (short-circuit protection)Output current: 100 mA max.Output saturation voltage: 1.5 V max. 1.5 V max.Response time: 250 us max.Switching frequency: 2KHz max.Indicators: OUTPUT LED (YELLOW); STABILITY LED (GREEN) mod. B01/F01POWER ON LED (GREEN) mod. G00Setting: Trimmer (250°) 6 turns screwDetection Mode Setting: LIGHT/DARK TrimmerOperating temperature: -10 … +55 °C (-10 … +50 °C UL Listed)Storage temperature: -25 … +70 °C no freezing or condesationOperating distance (minimum): 0.3...10 m on R2 0...30 m 20…250mm(white paper 200x200 mm)Insulating strength: 500 Vac 1 min., between electronics and housingInsulating resistance: >20 M 500 Vdc, between electronics and housingAdjustable setting range: --- 40…300 mmDifference on White 90% / Gray 18%: --- 10%Minimum sensing object (typical): Ø6 mm @ 3 m(opaque) Ø6 mm @ 3 m (opaque) Ø0.2 mm @ 170 mm(copper wire)Emission type: Red Laser diode(Emission wavelength: 650nm)IEC/JIS CLASS1 * ; Maximum output: 7mWAmbient light rejection: according to EN 60947-5-2Vibration: 0.5 mm amplitude, 10 … 55 Hz frequency, for every axis (EN60068-2-6)Shock resistance: 11 ms (30 G) 6 shock for every axis (EN60068-2-27)Housing: Body PBT / indicators cover PCLenses: PMMAProtection class: IP67Connections: 2 m cable  3.5 mm / M8-4 pole connector **Weight: 50 g. max. cable versions / 10 g. connector versions* This product complies with FDA regulations 21CFR 1040.10 and 1040.11 based on Notice No.50.** Use a UL Listed (CYJV/CYJV7) mating connector/cord assembly when using connector type as UL/c-UL listed products.SETTINGAlignment S3Z…B01Position the sensor and reflector on opposite sides.Turn the sensitivity trimmer to maximum. Find the points wherethe yellow LED (OUT) is switched ON and OFF in both verticalAlignment S3Z…M01Referring to the table below, adjust the distance of the photoelectric sensorwhen necessary. The table explains the status of operation LED when theoperation mode is set to light ON.and horizontal positions, and fix the sensor in the centrebetween these points. Optimum operation is obtained when thegreen LED is ON.If necessary, reduce sensitivity using the trimmer, in order todetect very small or transparent targets. In order to improvealignment, repeat the procedure detailed above whilstprogressively reducing the sensitivity.Alignment S3Z…F01/G00Position the sensors on opposite sides.Find the points where the yellow LED (OUT) is switched ON andOFF in both vertical and horizontal positions, and fix the sensorin the centre between these points.Optimum operation is obtained when the green LED is ON.Step Distancecontrol Adjusting procedure1Install a photoelectric sensor and the sensingobject. Turn the control counter-clockwise until theoperation LED turns OFF. Then turn clockwise untilthe operation LED turns ON (point A).2 Remove the sensing object, then the operation LEDturns OFF. Turn clockwise until the operation LEDturns ON, the background is detected (point B).3 Set the middle point between point A and B aspoint C.DIMENSIONSSAFETY PRECAUTIONSCAUTION - use of controls or adjustments or performance of proceduresother than those specified in this mannual may result in hazardous radiationexposure.ATTENTION - L'utilisation des commandes, ainsi que les modifications deréglages ou de procédures d’exécution autres que ceux specifiés dans cemode d'emploi peut entraîner une exposition à des rayonnements dangereux.This product emits a visible laser beam. Do not stare into the beam directly.Furthermore, do not look the laser which is reflected at a mirror-like object.About safety standards of laser product, IEC60825-1 ”Safety of laser products”has been stipulated by the IEC (International Electortechnical Commission).This product is classified as “CLASS1 product” according to IEC60825-1(2007). Use a UL Listed (CYJV/CYJV7) mating connector/cord assembly whenusing connector type as UL/c-UL listed products.CAUTION - This Product complies with21 CFR 1040.10 and 1040.11 except fordeviations pursuant to Laser Notice No.50, dated June 24, 2007, issued byCDRH (Center of Devices andRadiological Health) under FDA (Foodand Drug Administration).ATTENTION - Ce produit est conformeaux normes 21 CFR 1040.10 et 1040.11,à l'exception des dérogations relatives au document « Laser Notice No.50 » du24 juin 2007 émis par CDRH (Center of Devices and Radiological Health) de laFDA (Food and Drug Administration).Labels: Following “Warning label” and “Certification/ Identification label” areaffixed on this product according to IEC 60825-1 and laser regulation of FDA.When this product will be incorporated into final device system which isexported to the USA, make sure that Certification/Identification label is affixed.The sensors are NOT safety devices, and so MUST NOT be usedin the safety control of the machines where installed.Datalogic S.r.l.Via S. Vitalino 13 - 40012 Calderara di Reno - ItalyTel: +39 051 3147011 - Fax: +39 051 3147205 - www.datalogic.comHelpful links at www.datalogic.com: Contact Us, Terms and Conditions,Support.The warranty period for this product is 36 months. See General Terms andConditions of Sales for further details.Under current Italian and European laws, Datalogic is not obliged to takecare of product disposal at the end of its life. Datalogic recommendsdisposing of the product in compliance with local laws or contactingauthorised waste collection centres.© 2012 - 2017 Datalogic S.p.A. and/or its affiliates  ALL RIGHTS RESERVED. Without limiting the rights under copyright, no part of this documentation maybe reproduced, stored in or introduced into a retrieval system, or transmitted inany form or by any means, or for any purpose, without the express writtenpermission of Datalogic S.p.A. and/or its affiliates. Datalogic and the Datalogiclogo are registered trademarks of Datalogic S.p.A. in many countries, including theU.S.A. and the E.U. All other trademarks and brands are property of theirrespective owners. Datalogic reserves the right to make modifications andimprovements without prior notification.821003302 (Rev. C)OK OK NO

/ 2

Related manuals for Datalogic S3Z LASER Series