Datalogic S5N-PH Series Instruction Manual
This product is covered by one or more of the following patents.European Patent 851,211 B1; 1,111,690 B1; 1,148,346 B1; 1,209,487 B1.Italian Patent IT 1,321,772.S5N-PH/MH SERIESINSTRUCTION MANUALIEC 60825-1 “Caution – use of controls or adjustments or performance ofprocedures other than those specified herein may result in hazardousradiation exposure”CONTROLSOUTPUT LED (S5N-PH/MH…B01/C01/F01)The yellow LED ON indicates that the N.O. (normally open) output statusis closed.POW ER ON LEDThe green LED indicates that the sensor is operating.TRIMMER (S5N-PH/MH…B01/C01/F01)The trimmer can be used to adjust sensitivity; the operating distanceincreases turning the trimmer clockwise.W ARNING: The trimmer rotation is limited to 270° by a mechanical stop.Do not apply excessive torque when adjusting (max 40 Nmm).INSTALLATIONS5N-PH: The sensor can be fixed by means of the M18x1 threaded bodythrough a 18 mm hole, using the specific washer and the two CH.24nuts enclosed (1.5 Nm maximum tightening torque).Amongst the various possible solutions, we suggest to choose thecombination that offers the best visibility of the signalling LEDs and theeasiest access to the trimmer.22 mm nuts, h=8 mm, (2 Nm maximum tightening torque) are available toguarantee an improved torque.S5N-MH: The sensor can be fixed by means of the M18x1 threaded bodythrough a 18 mm hole, using the two CH.24 nuts enclosed (22 Nmmaximum tightening torque).Various orientable fixing brackets for both plastic and metallic versionsare available to ease sensor positioning (please refer to the accessorieslisted in the general catalogue).The operating distance is measured from the front surface of the sensorlens.CONNECTIONSThe connections are compliant to the EN 60947-5-2 standard.S5N-PH/MH…B01/C01/F01+ 10 … 30 VdcN.C. OUTPUTBROWN 1WHITE 2BLACK 4BLUE 3N.O. OUTPUT0 V S5N-PH/MH…G00+ 10 … 30 VdcTEST +BROWN 1WHITE 2BLACK 4BLUE 3NOT USED0 V M12 CONNECTOR2314DIMENSIONS24=1.5442=3.8TRIMMERmm=S50-MH VERSIONPOWER ON LEDOUTPUT LEDS50-PH VERSION694236withoutLXX1M O D E L S794346XX1LOUTPUT LEDPOWER ON LEDX4LX79436938CABLE VERS.OUTPUT LEDPOWER ON LEDØ4POWER ON LEDOUTPUT LEDCABLE VERS.L14123.514.514trimmertrimmerwithM O D E L Swithouttrimmertrimmerwith2414.5152510 10M12M18x1N°.2 Ø3.86°1412 414.514.5 10M18x16°61M1210Ø4TECHNICAL DATAS5N-PH PLASTIC VERSIONS S5N-MH METAL VERSIONSPower supply: 10 … 30 Vdc limit valuesRipple: 2 Vpp max.Current consumption(output current excluded):35 mA max. (mod.B01/C01/F01)30 mA max (mod.G00)Outputs: N.O. and N.C.; PNP or NPN (short-circuit protection)Output current: 100 mA max.Output saturation voltage: 2 V max.Response time: 333 sSwitching frequency: 1.5 kHzIndicators: OUTPUT LED (YELLOW) (mod.B01/C01/F01)POWER ON LED (GREEN)Setting: sensitivity trimmer (mod.B01/C01/F01)Operating mode: LIGHT mode on N.O. output / DARK mode on N.C. output (mod.C01)DARK mode on N.O. output / LIGHT mode on N.C. output (mod.B01/F01)Operating temperature: -10 … 50 °CStorage temperature: -25 … 70 °CInsulating strength: 500 Vac 1 min., between electronics and housingInsulating resistance: >20 M 500 Vdc, between electronics and housingOperating distance (typical values): B01: 0.1…9 m on R2 reflectorC01: 0…25 cmF01/G00: 0…50 mEmission type: RED LASER: Class 1 IEC 60825-1 (2014) (mod.B01/C01/G00)Class 1 CDRH 21 CFR PART 1040.10 (mod.B01/C01/G00)Max. power 1 mW; Pulse = 5 s; = 645…660 nm; Frequency 25 kHzAmbient light rejection: According to EN 60947-5-2Vibrations: 0.5 mm amplitude, 10 … 55 Hz frequency, for every axis (EN60068-2-6)Shock resistance: 11 ms (30 G) 6 shock for every axis (EN60068-2-27)Housing material: PBT Nickel-plated brassLens material: PMMAMechanical protection: IP67 Metal versions type 1 enclosureConnections: 2 m cable 4 mm / M12 - 4 pole connectorWeight: 75 g. max. cable vers. /25 g. max. conn. vers. 110 g. max. cable vers. /60 g. max. conn. vers.SETTINGSetting of S5N-PH/MH…B01Position the sensor and reflector on opposite sides.Turn the sensitivity trimmer to the maximum position.Moving the sensor both vertically and horizontally, determine the powerON and OFF points of the OUTPUT LED and then mount the sensor inthe middle of the points defined.If necessary reduce sensitivity in order to detect very small targets.In order to improve alignment, repeat the given procedure whilstprogressively reducing the sensitivity.Setting of S5N-PH/MH…F01/G00Position the sensor and reflector on opposite sides.Turn the sensitivity trimmer to maximum: moving the sensor bothvertically and horizontally, determine the power ON and OFF points of theOUTPUT LED and then mount the sensor in the middle of the pointsdefined.If necessary, reduce sensitivity using the trimmer, in order to detect verysmall targets. In order to improve alignment, repeat the proceduredetailed above whilst progressively reducing the sensitivity.Setting of S5N-PH/MH…C01Turn the sensitivity trimmer to minimum: the OUTPUTLED is OFF.Position the target to detect in front of the sensor.Turn the sensitivity trimmer clockwise until theOUTPUT LED turns ON (Target detected state, pos.A).Remove the target, the OUTPUT LED turns OFF.Turn the sensitivity trimmer clockwise until the OUTPUT LED turns ON(Background detected state, pos.B).The trimmer reaches maximum if the background is not detected.Turn the trimmer to the intermediate position C, between the twopositions A and B.TEST FUNCTION (S5N-PH/MH…G00)The TEST+ input can be used to deactivate the emitter and verify that thesystem is operating correctly.The receiver output should switch when the test is activated while thebeam is uninterrupted.The input activating voltage range is 10…30 Vdc.Datalogic S.r.l.Via S. Vitalino 13 - 40012 Calderara di Reno - ItalyTel: +39 051 3147011 - Fax: +39 051 3147205 - www.datalogic.comHelpful links at www.datalogic.com: Contact Us, Terms andConditions, Support.The warranty period for this product is 36 months. See General Termsand Conditions of Sales for further details.For information about the disposal of Waste Electricaland Electronic Equipment (WEEE), please refer to thewebsite at www.datalogic.com.© 2018 - 2019 Datalogic S.p.A. and/or its affiliates ALL RIGHTSRESERVED. Without limiting the rights under copyright, no part ofthis documentation may be reproduced, stored in or introduced into aretrieval system, or transmitted in any form or by any means, or for anypurpose, without the express written permission of Datalogic S.p.A.and/or its affiliates. Datalogic and the Datalogic logo are registeredtrademarks of Datalogic S.p.A. in many countries, including the U.S.A.and the E.U. All other trademarks and brands are property of theirrespective owners. Datalogic reserves the right to make modificationsand improvements without prior notification.826000422 Rev.CMIN MAXABCCLASS 1 IEC 60825-1 (2014)LASER PRODUCT S5N-PH VERSION S5N-MH VERSIONTRIMMER |
Related manuals for Datalogic S5N-MH Series
Datalogic Gryphon-HC Series Instructions Manual
Datalogic PowerScan 950X Series Instruction Manual
Datalogic Lynx Instruction Manual
Datalogic Lynx Instruction Manual
Datalogic DV9500 Series Installation Manual
Datalogic Magellan 1100i Instructions Manual
Datalogic Magellan 1100i Instructions Manual
Datalogic PowerScan 7000 2D Instructions Manual
Datalogic Magellan 3200VSi Instructions Manual
Datalogic Magellan 2200VS Installation Instructions Manual
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine