Datalogic Single Ethernet Cradle Datalogic Memor User Manual

Also see for Memor: User manual User manual User manual User manual User manual

Datalogic Single Ethernet Cradle Datalogic Memor User Manual Manual pdf 1 page image

Datalogic Memor™ Single Ethernet CradleNOTERead this manual carefully before performing any typeof connection through the Datalogic Memor™ SingleEthernet Cradle.The user is responsible for any damages caused byincorrect use of the equipment or by inobservance of theindication supplied in this manual.NOTEDo not attempt to disassemble the Datalogic Memor™Single Ethernet Cradle, as it does not contain parts thatcan be repaired by the user. Any tampering will invalidatethe warranty.The Datalogic Memor™ Single Ethernet Cradle paired with one DatalogicMemor™ mobile computer builds a reading system for the collection,decoding and transmission of barcoded data.The communication between the mobile computer and host PC throughthe Datalogic Memor™ Single Ethernet Cradle may occur also by usingthe standard ActiveSync® connection.Figure 1 – Datalogic Memor™ Single Ethernet CradleA) LED IndicatorsB) Spare Battery SlotC) Mini USB ConnectorD) RS232 ConnectorE) Power JackF) Ethernet Port with LED indicatorsG) Switch Ethernet/USBThe Datalogic Memor™ Single Ethernet Cradle is a serialcommunication adapter between the host computer and the DatalogicMemor™ mobile computer. Power supply is required to be connected tothe Cradle only for ethernet communication.Since the Datalogic Memor™ Single Ethernet Cradle also functions as abattery charger, a power supply is required for battery rechargingoperations, both for the mobile computer and spare battery packrecharging. The spare battery pack recharging slot can supply a 1000mAh as well as a 2000 mAh Battery pac.822000820By inserting the Datalogic Memor™ into the cradle, data can betransmitted to the host and its battery begins charging if the power supplyis connected. In addition, a spare battery can be charged by inserting itinto the slot at the back of the Datalogic Memor™ Single Ethernet Cradleas shown in the following figure.Figure 2 – Datalogic Memor™ Single Ethernet Cradle Charging andCommunicationThe LEDs positioned on the front part of the Datalogic Memor™Ethernet Cradle (see figure below) indicate the cradle and sparebattery charger status:Figure 3 - LED IndicatorsFront LED indicatorsLED STATUSRed Constant Spare battery charging*Charger Green Constant Spare battery chargecompletedPower Green it is constant when thecradle is powered* During charging, the LED may turn off to indicate a temporarysuspension of charging.Ethernet Connector LED IndicatorsSolid Green Link establishedFlashing Green Link activityEthernetGreen LED(left) Off No link establishedOff 10 Mb connectionEthernetYellow LED(right) Solid Yellow 100 Mb connection (this model is notavailable)CONNECTIONSCAUTIONConnections should always be made with power OFF!USB CONNECTIONThe Datalogic Memor™ Single Ethernet Cradle can be connected to thehost by means of any standard Mini USB cable.Once the host has been turned on, insert the Datalogic Memor™mobile computer into the cradle.Figure 4 - USB ConnectionA) Host Computer C) Datalogic Memor™ SingleEthernet CradleB) Std Mini USB (i.e.94A051016 CAB-421)D) *Power Supply (only necessaryfor battery charging)* Recommended power supply: 94ACC1324 PG5-30P35 AC/DCPOWER SUPPLY EU/USA PLUG.NOTEBe sure that the switch is in the “USB” position.During switch operation from USB position to Ethernetposition and vice versa the mobile computer must not beinserted in the cradle.Spare batteryCharge Slot withSpare BatteryInsertedData Transmission andMobile Computer BatteryChargingSpare BatteryCharger LEDPower LEDAB CD*ABCDF GE

/ 2

Related manuals for Datalogic Memor