Datasensor SDS5-5 Series Instruction Manual
  |
SDS5-5 SERIESINSTRUCTION MANUALCONTROLSOUTPUT LEDThe yellow LED indicates the output status.STABILITY LEDThe green LED ON indicates that the received signal has a reservegreater than 30% compared to the output switching value.TRIMMERThe 4-turn trimmer can be used to adjust the operating distance; thedistance increases turning the trimmer clockwise.CONNECTIONS+BROWNBLACKWHITE12410 … 30 VdcBLUE 3NCNO0 V100 mA100 mAM12 CONNECTOR2314DIMENSIONS53.593.6OUTPUT LEDTRIMMER75.9STABILITY LED16.5AXIAL VERSIONM18x1AXIAL VERSION16.575.953.5M18x1TRIMMER OUTPUT LED2265.1M18x141.796.4TRIMMEROUTPUT LEDSTABILITY LEDRADIAL VERSION10.8 mm10.8RADIAL VERSION2265.141.7M18x1TRIMMERCABLE VERSIONS M12 CONNECTOR VERSIONS21.421.4OUTPUT LED8.8 9.29.28.8M12M12 M12STABILITY LED84.7 18.8STABILITY LED18.8 87.1TECHNICAL DATAPower supply: 10 … 30 Vdc; reverse polarity protectionRipple: 2 Vpp max.Current consumption(output current excluded): 30 mA max.Output: NC and NO, NPN or PNP; 30 Vdc max. (short-circuit protection)Output current: 100 mA max.Output saturation voltage: 1 V max NPN versions / 2 V max PNP versionsResponse time: 2.5 ms max.Switching frequency: 200 Hz max.Indicators: OUTPUT LED (YELLOW) / STABILITY LED (GREEN)Setting: operating distance 4-turn trimmer wiper idlesOperating temperature: -25 … 55 °CStorage temperature: -25 … 70 °CElectric shock protection: Class 2Cutoff distance adjustment range: 50 … 100 mmOperating distance: from 20 … 50 mm to 0 … 100 mm depending from cutoff adjustmentEmission type: RED (660 nm)Ambient light rejection: according to EN 60947-5-2Vibration: 0.5 mm amplitude, 10 … 55 Hz frequency, for every axis (EN60068-2-6)Shock resistance: 11 ms (approx. 30 G) 6 shock for every axis (EN60068-2-27)LIGHT/DARK selection: LIGHT mode on NO outputHousing: ABS UL 94V-OOptics head: PVCLenses: GlassProtection class: IP67 (TYPE 1 ENCLOSURE)Connections: 2 m cable ∅ 5 mm / M12 4-pole connectorWeight: 100 g. max. cable versions / 30 g. max. connector versionsSETTINGPosition the sensor and turn the operating distance trimmer tomaximum.Place the target opposite the sensor at a slightly greater distance thandesired.Turn the trimmer counterclockwise until the sensor switches.Verify the adjustment moving the target closer and further the sensor;tune the adjustment if necessary.It is recommended to operate with the stability LED turned ON.The white/grey remission diagram is shown below:Grey test card (18% reflectance) cutoff point variation relative to white testcard (90% reflectance).DECLARATION OF CONFORMITYWe DATASENSOR S.p.A. declare under our sole responsibility thatthese products are conform to the 89/336 CEE, 73/23 CEE Directivesand successive amendments.WARRANTYDATASENSOR S.p.A. warrants its products to be free from defects.DATASENSOR S.p.A. will repair or replace, free of charge, any productfound to be defective during the warranty period of 36 months from themanufacturing date.This warranty does not cover damage or liability deriving from theimproper application of DATASENSOR products.DATASENSOR S.p.A. Via Lavino 26540050 Monte S. Pietro - Bologna - ItalyTel: +39 051 6765611 Fax: +39 051 6759324http://www.datasensor.com e-mail: info@datasensor.comDATASENSOR S.p.A. cares for the environment: 100% recycledpaper.DATASENSOR S.p.A. reserves the right to make modificationsand improvements without prior notification.826000263 Rev.C0%2%4%6%8%10%12%0 20 40 60 80 100 120DISTANCE (mm)PERCENT DEVIATIONSTRAIGHTVERSION90° VERSION |
Related manuals for Datasensor SDS10-5-M12-30
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine