Davey Lighting Original BTC 7401 Instruction Manual
  |
Ship’s Well Glass LightInstruction Manualv1.2-10.20 7401Safety & Installation Instructions1. If you are in any doubt consult a qualified electrician as to the installation of the fitting. Install in accordance with currentIEE wiring regulations. It is recommended that this fitting is installed by a qualified electrician.2. Ensure that the electrical supply is OFF. Disconnect the electrical supply at the fuse-board.3. If removing an existing fitting first, note all wiring connections: record which of the house wires is connected to the live,neutral and earth terminals.4. Carefully identify where the supply cable is (and check there are no other cables in the area) to avoid damage to concealedwiring during installation.5. Position the light where desired ensuring that there is suitable support adjacent to where you will connect to the housesupply and mark position of fixing holes, before drilling appropriate holes as below.6. a. Brick or masonry: Drill holes into which the wall plugs tightly fit, then insert wall plugs.b. Wood: No hole necessary (unless small pilot hole required), screws can be screwed directly into the timber.c. Plaster/Cavity: Special cavity wall fittings are required, rather than provided fixings. These are widely available fromgood hardware or DIY store and should come with their own instructions that must be followed. It may be easier torelocate the fitting so that you screw directly into a timber joist or beam.7. Support the fitting so that no strain is applied to the wiring when making the electrical connections. If necessary get acolleague to help.8. Electrical connection: this light fitting must be earthed. Make connections following the diagram below using the terminalblock provided. A small flat-head screwdriver is required.9. Double check all the connections are secure and that no loose strands of wire are left out of the connector. Ensure the lid ofthe terminal block is closed securely after making the connections.10. Check that no wires are trapped behind or within the fitting and complete the installation, referring to the Installationdiagram inside.11. Fit the correct type and wattage of lamp (or less). Be careful not to overtighten the lamp.12. Switch on at the fuse-board. Your light fitting is now ready for use.Other Important InformationSwitch off at mains before changing lamp(s). Never fit a lamp of greater wattage than recommended. Ensure children do notplay with the light fitting. Dispose of old lamps carefully. Never leave a fitting without a lamp in position (or someone canaccidentally touch the contacts). Adjust fitting only when power to the fitting is off and has been left to cool. If the externalflexible cable or cord of this luminaire becomes damaged, it shall exclusively be replaced by the manufacturer or his serviceagent, or similar qualified person, in order to avoid a hazard.These instructions are provided for your safety in order to prevent the risk of Fire, Electric shock or Injury. It is vitallyimportant that they are read in their entirety before installing your fitting. Please retain for future reference.MADE IN BRITAINORIGINALBTC.COM+44 (0)1993 882 251UNIT 21 / 22 AVENUE ONE, STATION LANE, WITNEY, OX28 4XZ, ENGLANDLNLiveKEYNeutralEarthL =N ==*MainsSupplyFitting*After 2004, wiring installation colours changed:LIVE Brown replaces RedEARTH Green/Yellow sleevingNEUTRAL Blue replaces BlackBROWNGRN/YELBLUEBROWNGRN/YELBLUEEstablished in 1990, Original BTC manufactures relaxed, familiar lighting for traditional and contemporary homes.All products are hand-assembled in Oxford from high quality components, produced in the UK.Cleaning and MaintenanceMetal finishes should only be cleaned with a soft, dry cloth. Do not use polishes or abrasives. Glass can be cleaned by hand,using a soft damp cloth with a window cleaner if necessary. Switch off power to the fitting before cleaning. Spare parts areavailable for this product, please contact us on the details below. |
Related manuals for Davey Lighting Original BTC 7401
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine