Delta 59348 Series Quick Start Manual

Delta 59348 Series Quick Start Manual Manual pdf 1 page image

172639 Rev. DModels/Modelos/Modèles59348, 59310 WH 59410, 59710,59310-WH20-PK, 59310-WH18-PK, 59348-20-PK, 59348-18-PKSeries/Series/SeriaHAND SHOWER UNIT WITH WALL MOUNTINSTRUCCIONES PARA LA INSTALACION DELA UNIDAD DE LA REGADERA DE MANO CONSOPORTE DE PAREDINSTRUCTIONS D’INSTALLATION DE LADOUCHE À MAIN AVEC SUPPORT MURAL72639Write purchased model number here.Escriba aquí el número del modelo comprado.Inscrivez le numéro de modèle ici.01/13/2023www.deltafaucet.com1-800-345-DELTA (3358)customerservice@deltafaucet.com?4 CONNECT TAPERED END OF HOSE TO HAND SHOWERSeat the washer, if provided, firmly into the hose nut. Remove the yellow tape from the end of the hose that screws onto the hand shower. Carefully align the threadof the tapered end of the Hose directly to the Hand Shower. Hand tighten - do not use a wrench or pliers. Then place the Hand Shower into the wall mount.3. INSTALL SHOWER ARM AND HAND SHOWERIt is recommended to wrap plumber tape (not included) around the threads of the shower arm only.3A. STANDARD INSTALLATION: A washer, if provided (some of our hoses are washerless), must be firmly seated into the bottom of the standard hex nut endof the Hose. Then firmly hand tighten the hose nut clockwise onto the water supply. DO NOT use a wrench or pliers. If your Hose has Hose nuts, as picturedin 3A; a vacuum breaker may be required for installation.If your hose is not equipped with a vacuum breaker, in order to make your product backflow compliant a vacuum breaker will need to be added.INSTALLATION WITH A VACUUM BREAKER: If a Vacuum Breaker is required for your installation, the Vacuum Breaker should be connected to the standardhex nut of the Hose and then attach it to the Shower Arm at the water supply connection. If you attach the Vacuum Breaker to the Hand Shower, it will notfunction as desired.3B. VACUUM BREAKER HOSE INSTALLATION: Your shower hose is equipped with a Vacuum Breaker, permanently installed in the end of your hose that hasa ridged nut (as pictured in 3B). Hand tighten the ridged nut clockwise to the water supply. Do not use a wrench or pliers. If you attach the ridged nut tothe hand shower, the Vacuum Breaker will not function.NOTE: A Vacuum Breaker is a device that is required by certain code authorities to protect your water supply from the back-flow of impure water. The VacuumBreaker usually discharges a small amount of water each time you turn on your shower. It may also drain water when you shut it off. Both are normalconditions – the water is draining not leaking.DO NOT TRY TO REMOVE OR TIGHTEN THE VACUUM BREAKER which is permanently installed into the hose. This could cause damage to themechanism.1. REMOVE EXISTING SHOWER HEADTurn the existing shower head counter-clockwise with adjustable wrench or pliers. Use care not to unscrew the shower arm; hold the shower arm secure. Note: Ifyour shower arm has a ball on the end of it, it will not work with this shower unit and will need to be replaced with a standard shower arm.2. INSTALL WALL MOUNTSelect wall position desired for your hose length. Prior to mounting, hold up the gray mounting base with the circular handle in an ”up” position. Determine type ofmount for your application. For mounting into Tile: Drill 1/4” holes in grout (if possible) and use enclosed anchors and screw mount to base. For mounting intoFiberglass/Acrylic: Drill 1/4” holes (larger if needed for specific toggle bolts) in wall and install with small toggle bolts (not supplied).For Adhesive Mounting: Clean the surface area with extra-fine steel wool; then apply rubbing alcohol or fingernail polish remover to prepare the surface and wipeclean. Caution: The first position must be correct, as you cannot move the mount after adhering to the surface. Peel off the green backing film and positionholder upright. Press firmly into place. ALLOW 24 HOURS BEFORE USING. Snap shell cover over the base on the wall.1. 2. 3. 4.RidgedNut= 3 A= 3 B

/ 4

Related manuals for Delta 59310 WH