Delta Electronics Program Copy Card TP-PCC Instruction Sheet

Contents

electrical specifications

Delta Electronics Program Copy Card TP-PCC Instruction Sheet Manual pdf 1 page image

Warning TP-PCC01 doesn’t support plug and play function. Please turn off power before plugging. The voltage for TP-PCC01 is supplied from TP extension slot. Please ensure that plug direction is correct when connectingTP-PCC01 to TP extension slot in case danger and damage on the device may occur. Introduction Electrical SpecificationsModel NameItem TP-PCC01Data Reserved Life / Times forWriting In 20 years / one hundred thousand timesOperation Temperature 0ºC ~ 55ºCWeight / Dimensions 6g / 50.85×19.8×10 mm Program Copy Card FunctionsCompatible firmware version: TP05G/TP08G (V1.00 and above)Using program copy card functions can copy the whole system parameters and application programs set inone TP05G/TP08G to another TP05G/TP08G rapidly. It can save much time and manpower. The operation isdescribed in the following sections.TP-PCC01 : Program Copy CardTP : Terminal Panel (TP05G/TP08G Series)Step TPTP-PCC01(Copy TP program to TP-PCC01)TP-PCC01TP(Copy program in TP-PCC01 to TP)1 Turn the switch on the TP-PCC01 toTPTP-PCC01Turn the switch on the TP-PCC01 toTP-PCC01TP2 Insert the TP-PCC01 into the extension slot of TP Insert the TP-PCC01 into the extension slot of TP3 Apply power to TP Apply power to TP4 If the model type of TP does not match themodel type of the program set in TP-PCC01:(TP05G program and TP08G program can’t becompatible with each other. It means thatTP05G program can’t be opened and edited byTP08G, and TP08G program can’t be openedand edited by TP05G either.)TP will display:TP series and TP-PCC01 is differentPress Enter to ConfirmTP seriesTP-PCC01Press Esc to ExitPress CLR to Erase TP-PCC01 If there is no program in TP-PCC01.TP will display:The TP-PCC01 is EmptyTP-PCC01 TP seriesis illegalModel Name ExplanationProgram Copy CardSeriesENGLISH Remove the programTP will display:TP-PCC01 will be Erased!Press Enter to ConfirmPress ESC to Exit If the model type of TP does not match themodel type of the program set in TP-PCC01.TP will display:TP series and TP-PCC01 is differentPlease Remove the TP-PCC01and Reboot If the model type of TP and the model type ofthe program set in TP-PCC01 is matched.TP will display:Press Enter to ConfirmTP seriesTP-PCC01Press Esc to ExitPress CLR to Erase TP-PCC01Press key to confirm the “writing in”operation. If the model type of TP and the model type ofthe program set in TP-PCC01 is matched.TP will display:Press Enter to ConfirmTP-PCC01 TP seriesPress Esc to ExitPress key to confirm the “writing in”operation. When executing “writing in” operation,TP will display:TP series TP-PCC01Please wait! When executing “writing in” operation,TP will display:TP-PCC01 TP seriesPlease wait!5 “Writing in” operation is completed.TP will display:Please Remove the TP-PCC01 andRebootPlease turn the power of TP off and removeTP-PCC01 from TP. At this time, all TP programsand system parameters have been copied toTP-PCC01. “Writing in” operation is completed.TP will display:Please Remove the TP-PCC01 andRebootPlease turn the power of TP off and removeTP-PCC01 from TP. At this time, all programs andsystem parameters stored in TP-PCC01 havebeen copied to TP.6Turn the power of TP off and then removeTP-PCC01 when the message “Please Removethe TP-PCC01 and Reboot” displays on thescreen of TP.Turn the power of TP off and then removeTP-PCC01 when the message “Please Removethe TP-PCC01 and Reboot” displays on thescreen of TP. Dimension and Installation（Units: mm）Note:To avoid damage to TP-PCC01, when installingTP-PCC01 into TP, please pay particular attentionto the installation direction of TP-PCC01 and ensurethat the side which there is a switch on it should beup and toward the user.

/ 2

Related manuals for Delta Electronics Program Copy Card TP-PCC