Denali HMT.07.11000 Instruction Manual

Denali HMT.07.11000 Instruction Manual Manual pdf 1 page image

Instruction Rev040 mm 10 20 30 40 50 60 70 80 90Thank you for choosing DENALIWe know you would rather be riding your bike than wrenching on it, so we go the extramile to make sure our instructions are clear and as easy to understand as possible. Ifyou have any questions, comments, or suggestions don’t hesitate to give our gearexperts a call at 401.360.2550 or visit WWW.DENALIELECTRONICS.COMPlease Read Before InstallingDENALI products should always be installed by a qualified motorcycle technician. Ifyou are unsure of your ability to properly install a product, please have the productinstalled by your local motorcycle dealer. DENALI takes no responsibility for damagescaused by improper installation. Caution: When installing electronics it is extremelyimportant to pay close attention to how wires are routed, especially when mountingproducts to the front fender, front forks, or fairing of your motorcycle. Always be sureto turn the handlebars fully left, fully right, and fully compress the suspension toensure the wires will not bind and have enough slack for your motorcycle to operateproperly.Installation TipsWe strongly recommend using medium strength liquid thread locker on all screws,nuts, and bolts. It is also important to ensure that all hardware is tightened to theproper torque specifications as listed in your owner’s manual. For included accessoryhardware please refer to the default torque specifications provided below. Inspect allhardware after the first 30 miles to ensure proper torque specifications aremaintained.Hardware Sizing GuideNot sure what size bolt you have? Use this ruler to measure screws, bolts, spacers, etc.Remember, the length of a screw or bolt is measured from the start of the “mountingsurface” to the end of the screw, so only include the screw head when measuringcountersunk screws.M3 10.0 in-lbs - 1.0 NmM4 23.0 in-lbs - 2.5 NmM5 44.5 in-lbs 3.5 ft-lbs 5.0 NmM6 78.0 in-lbs 6.5 ft-lbs 9.0 NmM8 - 13.5 ft-lbs 18.0 NmM10 - 30.0 ft-lbs 41.0 NmM12 - 52.0 ft-lbs 71.0 Nmin-lbs ft-lbs NmBolt Size0in 1 2 3What’s In The Box?DENALIELECTRONICS.COMHMT.07.11000BMW R1250GSSplit Horn Mounting BracketInstruction Manual(a) Acoustic Horn Bracket......(HMT.07.014)................................Qty 1(b) Compressor Bracket......(HMT.07.013)....................................Qty 1(c) M8x75mm - SocketHead Screw............................................Qty 2(d) M8 Washer.........................................................................Qty 2(e) M8 Spacer...OD 19.05mm, ID 8.1mm, L 19.05mm...................Qty 2(f) M6 Spacer...OD 9.53mm, ID 6.53mm, L 7.938mm...................Qty 1(g) M6 Washer..........................................................................Qty 2(h) M6x25mm - Lens Head Screw................................................Qty 2(i) M8 Nut Cap.........................................................................Qty 1Kit ContentsTools Required: 13mm Wrench, 10mm Wrench, 6mm Allen Key, 4mmAllen Key, T30 Torx Bit for factory screw removal.(a) (b)(c) (h)(f)(g)(i)(e)(d)

/ 2

Related manuals for Denali HMT.07.11000