Eaglemaster CA-168 Manual And Installation
  |
- Product description:IMB-3 is a high security level vehicle protection system with an anti-theft function for bothparked and moving vehicles. A vehicle equipped with this immobilizer can only be used if thepersonal transceiver (TAG) is within range, either inside the vehicle or no further than 2 maway. If the engine is switched on without the TAG, after 10sec the system will warn thedriver by buzzer for 10sec (the first 5sec with intermittent 1-beep sound, and 5sec withintermittent 2-beep sound). After, if the system detects a car movement again it will be(engine blocked) for 10sec. The next time you start the engine without the TAG in around5sec. You will hear intermittent 2-beep sound for 20sec.If you turn the ignition on and the TAG is located in the range, the established relationbetween main unit and TAG will be confirm by a melody sound.The first (internal) blocking algorithm is described below:If you wish to drive, the IMB-3 immobilizer TAG must be located inside the vehicle. Thesystem will allow you to start the engine without the TAG, but the engine will be immobilizedeach time you make the ignition.After the engine's immobilization, the system allows you to start the engine again by turningoff and on the ignition. Moreover, each attempt to drive, the engine will be immobilized againuntil the TAG is place in the range or the personal emergency disabling code (PIN code) isused..The anti-theft function will automatically proceed when the TAG is located out of the rangewith the ignition switched on. For the first 35 seconds, the system will continue to wait for asignal from the TAG. Then, the driver will be warned 20sec with the intermittent beep sound(in the first 10sec with 1-short beep continuing with 10sec by 2-short beep). Then thesystem will be immobilized for 10sec (engine blocked). Furthermore, if the system detectsany movement again in the car, it will be immobilized for 10sec. If you turn the ignition offand on again you will hear 2-beep intermittent sound for 20sec and it will be immobilized for10sec if the system detect any movement of the car.The second (external) blocking circuit algorithm is very simple: there is no TAG - theexternal relay blocks the starter:CA-168 AUTO IMMOBILIZER Manual and installationTo use the vehicle without a TAG you will require a special PIN code consisting of twodigits (for example, 1 & 2).The manufacturer will provide you a card with the PINcode. The system is already coded with 1,2 (default setting).(1) Turn on and off the ignition for 5 times and stay in off position;(2) Wait until 2-beep sound emits inside the vehicle;(3) Turn on the ignition and prepare to enter the PIN code. Then, the warningsignals beeps will start to sound, and you should count them. In this example, wait forthe first (1st) beep, when it sound turn off the ignition. (In this example, the first digit"1" of the PIN code has been entered);(4) Turn on the ignition and proceed to count the warning signals beeps until thenumber aligns with the second digit of the PIN code (e.g. 2), then turn off the ignition.(In this example, the second digit "2" of the PIN code has been entered);(5) Wait until you hear a melody sound inside of the vehicle. The system now is inprogramming mode and disarmed;Note:- If you make a mistake while entering the PIN code will sound a 4-short beep, and youwill have to repeat the procedure from step 1 entering the new PIN code.- Within 20sec without any ignition activation the system will auto exit the mode andyou will hear 2-long and 2-short beep sound.<< Driving without a TAG - follow the step 5 >>- Follow the step 5 turning on the ignition and you will hear 2-long and 2-short beep.The system will allows you to start the engine without a TAG.- The next time you want start engine without a TAG, it will be require the PIN codeagain.<< Valet mode - follow the step 5 >>- Follow the step 5 turning on and off the ignition only 1 time and stay in off position;- After 3sec you will hear 1-long beep sound. The system is indicating the entrance toa Valet Mode.- In a Valet Mode, each time the ignition is turned on, you will hear 2-short beepsound notifying that the Valet Mode has being activated. Remember that in this modethe vehicle will not be immobilize without the TAG.- To exit the Valet Mode, you should turn on and off the ignition 5 times and stay in offposition. Then, you will hear 2-long and 2-short beep indicating that the system isgoing out of the Valet Mode.<< New PIN code setting - follow the step 5 >>- Follow the step 5 turning on and off the ignition 3 times and stay in off position;- After 3sec you will hear 2-long beep sound. The system is indicating that he isready to set a new PIN code;- Emergency system disabling / Programming mode:-Using the product- Anti-theft function- Disarm mode:OFFONIgnitionswitching on whenTAG is detectedTAG detectionmelody2nd circuitblockingis disabledOFFON2nd circuitblockedIntermittentbeep soundIgnitionswitching on whenTAG is not detected |
Related manuals for Eaglemaster CA-168
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine