Eaton SPD150i Technical Specifications And Installation Manuallines

Also see for SPD150i: Installation guide

Eaton SPD150i Technical Specifications And Installation Manuallines Manual pdf 1 page image

Specifications are subject to change without notice. Copyright 2012 Eaton Industries, Mascot. NSW.Technical Specification SPD150iDoc# 5100SPD150iPage 1 of 2TECHNICAL SPECIFICATION ANDINSTALLATION GUIDESPD150i SURGE DIVERTER( IEC61643-11 Class I & II, 150kA, 2 mode, 220-300vac, L-E or L-N )APPLICATIONS• Primary power circuits• Telecommunication Systems / Rectifiers• Process and Control Systems• Computer Systems / Medical SystemsFEATURES• Patented MTMOV technology( Failsafe thermal disconnect )• UL1449 ed3 Type 4 listed components• 150kA, 2 mode, L-N or L-E• UL94-V0 ABS din rail mount housing• Din 43880 form factor 4 din wide• Dry contact alarm• LED visual indicators for protection,power and fault conditions.FUNCTIONAL DESCRIPTIONThe SPD150i is designed to protect single and threephase power systems against damage from surgesand spikes caused by lightning and other electricalsources. The unit is intended for point of entry ormain board protection and is connected in parallelwith the power system via HRC fuses.This model ( SPD150i ) is designed for use insystems with a grounded neutral in L-N mode. Ifyour system does not have a grounded Neutral oris of a different voltage, this model is NOTsuitable.OPERATIONIndicators - The operation status of the SPD150i isindicated by leds on the front panel. The ‘OK’ ( blue )light indicates that power is applied to the SPD150iThe ‘FAULT’ light ( red ) indicates that the surgeprotection circuitry is damaged and the unit should bereplaced. The additional 3 leds ( blue ) indicate thestatus of each MOV element. When the fault indicatorlights, the protection relay contacts change over. Thepower failure alarm will operate when mains voltagefalls below 180VAC.PHYSICAL AND ELECTRICAL SPECIFICATIONSModel SPD150iNumber of ports 1 PortMethod of mounting Fixed. DIN Rail mountInput voltage – Uc 220-300vac 1P, 380-480vac 3PMaximum continuous voltage –MCOV 320 L-N, L-ETemporary overvoltage - TOV 350VAC L-N, 15 minsService typeTT, TN, TN C-S or any 1 or3phase system with agrounded neutral.Test classification (IEC61643-11) Class IIMaximum over current protection 125AProtection modes Line-Neutral, Line-Earth,Inom 8/20us (Line-Neutral/Earth).Nominal surge life. 60kAImax 8/20us (Line-Neutral/Earth).Maximum surge level. 120kAResidual voltage (Vpl) (Line-Neutral/Earth). (Let throughvoltage)<1000v (3kA, 8/20us,( IEC61643-11)Safety disconnect Series thermal fusing onMOV’sExternal disconnectorrequirement Max 125A HRC fuseTerminations Power 16mm2Alarms/indicators5 LED display, drycontact alarm relayoutput – 250VAC/32VDC,5A, 5kV isolationEnclosure rating IP20Standards. Designed inaccordance with :IEC61643-11, ANSI/IEEEC62.41 Cat A & B,AS1768-2007 Cat A & B,UL1449ed3 type 4Installation instructions Supplied with unit.Dimensions 70 x 58 x 90 mm (WxDxH)Weight 200gEnvironment -10 to 60°C, 0 to 95%RH(non-condensing)Warranty 5 years, workmanshipand materials

/ 2

Related manuals for Eaton SPD150i