Ebelco 300-LED Installation Instruction Manual
Also see for 1200-LED: Installation instruction guideInstallation & user guide
  |
12 / 24 VDCPower Output12 VDCSetting24 VDCSetting12 / 24 VDCPower InputN.CC+ -N.OBasic Installation Concept & AccessoriesHall Effect SensorOutput(Only for LED Models)Hall EffectSensor Input(Only for LEDModels)LED Status:> Green = Locked> Red = Released> Off = No Input(Only for LED Models)SpecModel 600-SVoltage Input 12VDC / 24VDCDimension600-LED(L)250 x (W)42 x (T)25 (mm)1200-S12VDC / 24VDC1200-LED(L)266 x (W)67 x (T)39 (mm)300-LED(L)210 x (W)35 x (T)22 (mm)Current Draw12VDC / 24VDCOut SwingEM LockDoorFrameGeneral InstallationDoor FrameOut-SwingGlassDoorEM LockDoorU1 Bracket ForGlass DoorDSU Bracket ForGlass Frame & Glass DoorDoorOut-Swing EM LockDoorFrameZL Bracket ForIn-Swing DoorLS Bracket ForOut-Swing DoorDoorFrameDoorEM LockIn-SwingZL Bracket ForIn-Swing Door With CoverM4 SetScrew$/%XVKDoorFrameDoorEM LockP/H MC ScrewM4 x 8Self-tapping ScrewIn-SwingCSK M8 x16EM LockIn-SwingGlassDoorGlassFrame12/24 VDCPowerSelf-tapping ScrewMounting PlateCable WireArmature PlateSexnut BoltRubberWasherMetalWasherArmatureScrewFixing Screwx2Anti TamperNut x2PCB CoverCoverScrewGuide Pin x2Allen WrenchGeneral Installation Steps & Maintainance1. Drill the armature plate holes in the door using the sticker template provided.2. Attach the armature plate to the door with the hardware provided as per the illustration.3. With the door closed, mark the door frame at the edge of the armature in order to properly align theelectromagnet to the armature.4. Attach the mounting plate to the door frame using the self-tapping screws provided.Align the mounting plate with the mark from the previous instruction.5. Insert the wires through the hole in the mounting plate and into the electromagnet unit.Attach theelectromagnet unit to the mounting plate with the Allen head fixing screw.6. Screw in the anti-tamper nuts to prevent unauthorized access and m ake sure to fully tighten the fixingscrew with proper tool "T" Handle Allen Key.7. Connect the power wires accordance with NFPA 101 & all wiring to be completed inside protect area.8. Typical wiring method which shall be in accordance with CSA C22.1, Canadian Electrical Code, Part I,Safety Standard for Electrical Installations, Section 32.9. It is recommended that to apply a light coat of silicon lubricant to the mating surface on a monthly basisto prevent rust.Trouble Shooting1. Sensor not functioning- Improper attachment of electromagnet and armature plate- Modification of the PCB2. Door not locked- Incorrect wiring or no power from power supply3. Reduced holding force- Poor contact of electromagnet and armature.- Be sure armature is loose enough that it can fully contactelectromagnet along the entire length.- Mating surface is dusty or damaged.- Improper input voltage or wire size.Performance Level- Destructive Attack: Level I- Line Security: Level I- Standby Power: Level I- Endurance: Level IV(Relay Source #2 and #3)12VDC / 24VDC(L)250 x (W)42 x (T)25 (mm)12VDC / 24VDC(L)266 x (W)67 x (T)39 (mm)1-2Copyright ̹ E.I.S.B. All Right Reserved.EISB-EMS-IG Ver.A Publish:18.1.2019Remark: Drawing maybe differ from actual product.T Handle Allen Key480mA / 240mA 510mA / 285mA330mA / 185mA 420mA / 210mA 500mA / 265mAElectromagnetic LockInstallation Instruction Guide(Intend for use in indoor dry location)Set the jumper position accordingto the power input correctly beforeswitch ON the power.Caution Against ChangingFactory Applied Settings ! |
Related manuals for Ebelco 1200-LED
manualsdatabase
Your AI-powered manual search engine