Fein MSfo 880-ld Operating Instructions Manual

Fein MSfo 880-ld Operating Instructions Manual Manual pdf 1 page image

Operating instructionsfor the High Frequency Angle GrindersType MSfo 880-ld, MSfo 880-lcMSfo 880-1~ be handed to the workshop!and MSfo 880-ldK, MSfo 880-lcK {42 Volts)1. Technical DataType of current: 3 ph. A. C. 200/300 CyclesFrequency Speed Net weightType Input I Output(cycles) R.l'.M.IWatts HP lbs kgMSfo 880-1d} 200 8600 I 2400 2.5 21.8 9.8MSfo 880-1dK''. 300 8500 3400 3.5 21.8 9 .8MSfo 880-1c} 200 6500 2400 21.8 9.82.5MSfo 880-1cK''· 300 6SOO 3400 3 .5 21.8 9.8,,. Fo r 200 cycles only2. ConstructionThe grinder is provided with a robust surface air cool ed motor design-ed to withstand substantial overload . The internal parts are protectedaga inst dust by total enclosure. The h an dle moun ted switch is a ls oenclosed. Highe st po ss ible w orking safety is a tt ai ned by th e rubbersheating.The grinder MSfo 880-1 is an electric tool of class I wi th safe tyconductor according to VD E reg ul a tion s 0740. For saf ety reasons themark ed safety conductor of the supp ly ca ble, connected to the metalcasing of the machin e, mu st be connected to the prot ecting contact ofthe plu g. For good in sta ll atio n of h igh frequency we dr aw youra tt e nti on to general opera tin g a nd in stalla tion instructions No. B 22for High Frequency Tran sformers a nd High Frequency Circu it s. T y peMSfo 880-1 K is an electric tool of class III for low tension (42 Volts)without safety conductor. For saf et y reasons the housing of this g rin-der must not be eart hed .The bevel gears h ave helical teeth, gears are l appe d for accuratem es hin g. Both part s to be sup pli ed as pairs only. Gearings a nd bear-in gs are protec ted against du st and lo ss of grease.Part of the cooling air is led by ducts throu gh the gearing in the gearhead for additional cooling.BE 101/e X 9.65 Printed in Germ anyG rin ding wheel max .peripheral Thr ead ofmax. dia. I max. width I bore I typeIspeedI in . I mm ft /s I s pind lein. mm 1n . I mm ml s7 I 178 3/s 10 1/ s 22.2 260 80 M 147 178 3/s 10 1/s 22.2 elas t ic 260 80 M 149 230 3/s 10 7/s 22.2 disc 260 80 M 149 230 3/s 10 7/s 122.2 260 80 M 143. OperationFirst check that details on the rat ing plate agr ee with those of the hi ghfrequen cy supply.In o rd er to a void con stant overload, e.g. w hen cutting off , we re -commend the installation of a saf ety switch correspon din g to th erated current of the motor (see also sep a rated in struction B 22).Switch mu st be in th e "Off " position when connectin g.Check th at the tool rot ates in direction marked by arro w on them achin e, otherwi se the chucked tool may become loo se . To checkrotation switch on tool bri efly. If it does n ot follow a rro w, re verseby ch anging over t wo leads in the plug.Ty pe MSfo 880-1d, MSfo 880- ldK a nd MSfo 880-1c, MSfo 880- 1cKmust not be used w ithout wh ee l guards.Do not exceed the dim ensions of gr inding w heels stip ulated. Whenworking wi th crank wheel hold tool in such a pos itio n th at th eg rindin g wh ee l works under an ang le of 15- 30° . For cutti ng off usecutt in g-off w h ee l with the prescribed flanges, f or cut t in g off stoneuse our wheel gua rd w ith adjustable support.F urther mor e, the ha ndl e should be screwed into t he right ha nd bo reof the housing (seen from above) for cutting off, in order to pr eve ntthe grinding dust from being thro wn into the air inlet of the machin e.

/ 4

Related manuals for Fein MSfo 880-1