Fema C Series Quick Installation Manual
Also see for C Series: User manual
  |
Quick installation guide C60-FLwww.fema.esSeriesCHow to install the meter in a panel1. Remove the 2 blue fixation tabs from each sideof the unit.2. Insert instrument from the front of the panelinto panel cut out.3. Re-attached the 2 blue fixation tabs by slidingeach one along its rail on each side and push untilthe tabs are tight onto the panel. If needed use aflat screwdriver to push the tabs strongly to theend.2131. Front viewKey ‘LE’ Key ‘SQ’1. Enter into ‘Configuration menu’2. Validate parameter1. Exit the menuKey ‘UP’1. Enter into ‘Fast access’2. Next valueAlarm led1 & 2Units2. Dimensions and panel cut-out ‘mm’ (in.)Panelcut-outDetail of the femaleterminal provided.(includes terminal)91 mm(3.58 in.)96 mm(3.78 in.)48 mm(1.89 in.)44 mm(1.74 in.)92 mm(3.63 in.)16 mm(0.63 in.)75 mm(2.95 in.)8 mm(0.31 in.)3. Panel mount1. Open the instrument (see section 3)2. Connect the signal, the power and the rear controls (see section 6)3. Configure the instrument from the ‘Configuration menu’ (see section 13)4. If you need additional information, see section 8.!4. Installation and start-upC60 FLModel- - -Option 1-A1 (1 relay SPDT)-S1 (Modbus RTU)-M1 (analogoutput 4/20mA)-(empty)PowerU-U(Universalpower supply18...265 Vac/dc)-Option 2-A2 (1 relay SPDT)-(empty)Customization-XXXX (customizedexecution under request)-(empty).Series--NBT (no frontkeypad)-65 (front IP65)-(empty)Others5. How to orderModule A2 (relay)NCCom.NOG IHOption 2Module S1 (Modbus RTU)A B CCommonBAModule A1 (relay)A B CNCCom.NOModule M1 (4/20 mA)A B C4/20 mA+15 Vexc.Active outputA B CCommon4/20 mAPassive outputOption 1excitation voltage (+15 Vdc @50 mA)commonreads the background instrumentVexc0 VdcSignalControl 2Control 1 resets the total flow valueinput signal (impulses)1 2 3 4 5fuseProtection fuse values:250 mA time-lag for power voltage > 50 Vac/dc400 mA time-lag for power voltage < 50 Vac/dcOption 2 Option 11 2 3 4 5 8 9 0A B CG IH-Vdc/Neutral+Vdc/Phase(not connected)Power supply 18...265 Vac/dc(50 / 60 Hz) (<2.5 W) (isolated)6. ConnectionsKey ‘SQ’ (<) - press the ‘SQ’ (<) key for 1 second to access the ‘configuration menu’.Inside the menu, the ‘SQ’ (<) key functions as a ‘ENTER’ key. It selects and accessesthe menu option currently displayed. At menus with numerical value entries, it vali-dates the number displayed.Key ‘UP’ (5) - the ‘UP’ (5) key gives access to the ‘fast access’ menu. Inside themenus, it moves vertically through the different menu options. At menus with numeri-cal value entries, it modifies the digit selected by increasing its value to 0, 1, 2, 3, 4,5, 6, 7, 8, 9.Key ‘LE’ (3) - inside the menus, the ‘LE’ (3) key functions as the ‘ESCAPE’ key. Itleaves the selected menu, and eventually, will leave the whole menu. When leavingthe ‘configuration menu’ with the ‘LE’ (3) key, the changed parameters are activated.At menus with numerical value entries, the ‘LE’ (3) key allows to select the activedigit. To modify the value of the selected digit use the ‘UP’ (5) key.Menu ‘Rollback’After 30 seconds without interaction from the operator, the instrument will rollbackand leave the ‘configuration menu’ or the ‘fast access’ menu. All changes will be dis-carded.ExampleThe menu example indicated below is for information purposes only, and may notmatch the actual menu of the instrument.InputExample of operation inside the ‘configu-ration menu’.1. The ‘SQ’ (<) key enters into the ‘con-figuration menu’.2. The ‘SQ’ (<) key enters into the ‘InP’option menu.3. The ‘UP’ (5) key moves through themenu options.4. The ‘SQ’ (<) key selects the desiredrange and returns to the ‘InP’ menu.5. The ‘LE’ (3) key leaves the actual menulevel and moves to the previous menulevel.6. The ‘LE’ (3) key leaves the ‘configu-ration menu’. Changes are applied andsaved at this moment.(2)(3)(3)(3)(3)(3)(4)(4)(4)(4)(5)(5)(5)(5)(3)(3)(6)(6)(1)7. How to operate the menuUser’s manual C60-FL www.fema.es/docs/5046_C60-FL_manual_en.pdfDatasheet C60-FL www.fema.es/docs/5058_C60-FL_datasheet_en.pdfQuick installation guide C60-FL www.fema.es/docs/5060_C60-FL_installation_en.pdfCE declaration of conformity www.fema.es/docs/5047_CE-Declaration_C60-FL_en.pdfWarranty www.fema.es/docs/4153_Warranty1_en.pdf8. Additional documentationIf you need additional information, see section 8to download the full User’s Manual or check theQR code for a direct download.! User’s Manual C60-FL9. User’s manual10. Configuration exampleA flow sensor provides ‘NPN’ impulses, with a frequency proportional to the instantflow, with a ‘K factor’ value of ‘1.241804’ [impulses / liter].Configure the instrument to read the instant flow in [m3/hour] with 1 decimal point,and the total flow accumulated in [gallons] with 2 decimal points.By default instant flow must be on display, and access to the total flow value will bedone by activating the rear connector terminal.Reset of the total flow will be performed by pressing the front key left ‘LE’ (3).1. Instrument main configurationAt the ‘Instrument configuration’ (‘c.InS’) section :• at ‘Main instrument’ (‘MAIn’) select ‘rAtE’• at ‘Sensor’ (‘SnSr’) select ‘NPN’• at ‘‘K’ Decimal point’ (‘K.dP’) select ‘X.xxxxx’• at ‘‘K’ Factor’ (‘K.Ftr’) configure ‘1.24180’ (the last digit ‘4’ of the ‘K factor’ can notbe introduced)Validate changes and exit the ‘configuration menu’. At this moment, the instrument isconfigured and reads instant flow meter, in [liters/second].3. Scale the instant flow value to the desired units [m3/hour]At the ‘Instant flow configuration’ (‘c.rAt’) section :• at ‘Time Base (Multiplier)’ (‘tIME’) configure ‘3600’ (3600 seconds in 1 hour)• at ‘Divider’ (‘dIV’) configure ‘1000’ (1000 liters in 1 m3)• at ‘Resolution’ (‘rESL’) select ‘XXXXX.x’Validate changes and exit the ‘configuration menu’. At this moment, the instrument isconfigured and reads instant flow, in [m3/hour], with 1 decimal.4. Scale the total flow value to the desired units [gallons]Relation between liters and gallons is 1 liter = 0.2642 gallons.At the ‘Total flow configuration’ (‘c.tot’) section :• at ‘Multiplier’ (‘MuLt’) configure ‘2642’• at ‘Divider’ (‘dIV’) configure ‘10000’The total scaling factor is ‘2642’ / ‘10000’ = ‘0.2642’• at ‘Resolution’ (‘rESL’) select ‘XXXX.xx’Validate changes and exit the ‘configuration menu’. At this moment, the instrumentis configured and reads total flow in [gallons], with 2 decimals. To read the total ac-cumulated flow on display, close the rear contact ‘contact 1’.5. Configure ‘Key Left’ (3) to reset the total flow valueAt the ‘Key Left’ (‘K.LE’) section :• at ‘Reset ‘total’’ (‘rSt.t’) select ‘on’Validate changes and exit the configuration menu. At this moment, the total flow val-ue will reset to ‘0’ when the key ‘LE’ (3) is pressed.This instrument conforms to the actual CE regulations. For a copy of the ‘CE declarationof conformity’ see section 8. Applicable regulations are :Security regulations EN-61010-1 (‘Fixed’ equipment, ‘Permanently connected’. ‘Dou-ble’ isolation.)Electromagnetic compatibility regulations EN-61326-1This instrument does not provide a general mains switch and will start operation assoon as power is connected. The instrument does not provide protection fuse, and thefuse must be added during installation.According to directive 2012/19/EU, electronic equipment must be re-cycled in a selective and controlled way at the end of its useful life.Risk of electrical shock. Instrument terminals can be connected to dan-gerous voltage.Instrument protected with double isolation. No earth connectionrequired.Instrument conforms to CE rules and regulations.Standard warranty of 2 years according to actual european legislation.Free of cost warranty extension of 5 years, available at: http://www.fema.es/garantia.asp11. RegulationsFEMA ELECTRÓNICA, S.A. | Manufacturing for Industrial Automation | www.fema.es . info@fema.es501969-2019YEARS5Extended WarrantyYEARSElectromagnetic C.EN-61326-1SecurityEN-61010-1QCertified QualityISO 90015060r01QCertified QualityISO 9001Electromagnetic C.EN-61326-1501969-2019YEARSCounterFlow |
Related manuals for Fema C Series
manualsdatabase
Your AI-powered manual search engine