GE DSKS433EB3WW Installation Instructions Manual

GE DSKS433EB3WW Installation Instructions Manual Manual pdf 1 page image

Installation Instructions (USA onlg) !MODELS DSKS433 AND DSKS333 MUST BE INSTALLED WITH CONTROL PANEL AT BOTTOM IN ORDER TO OPERATE ADEQUATELY.Questions? Call: 800.GE.CARES (US) or visit our web site at: www.GEAppliances.com (US)BEFORE YOU BEGINReed these instructions completely end cerefullg.• IMPORTANT- Save these instructions for localinspector's use.• IMPORTANT- Observe all governing codes andordinances.• Note to Instoller - Be sure to leave these instructionswith the customer.• Note to Customer - Keep these instructions with yourOwner's Manual for future reference.• Before the old dryer is removed from service ordiscarded, remove the dryer door.• Service information and the wiring diagram are locatedin the control console.• Do not allow children on or in the appliance. Closesupervision of children is necessary when the applianceis used near children.• Install the dryer where the temperature is above 50°Ffor satisfactory operation of the dryer control system.• Product failure due to improper installation is notcovered under the Warranty.• Dryers installed in garages (if allowed by local codes)must be elevated 18 inches (46 cm) above the floor.-4LWARNING RISK OF FIRE• To reduce the risk of severe injury or death, follow allinstallation instructions.• Clothes dryer installation must be performed by a qualifiedinstaller.• Install the clothes dryer according to these instructions andin accordance with local codes. In the absence of local codes,installation must comply with the NATIONAL ELECTRICAL CODEANSI/NFPA NO. 70.• This dryer must be exhausted to the outdoors.• Use only 4" rigid metal ducting for exhausting the clothes dryer tothe outdoors.• DO NOT install a clothes dryer with flexible plastic ductingmaterials. If flexible metal (semi-rigid or foil-type) duct isinstalled, it must be UL listed and installed in accordance withthe instructions found in "Connecting The Dryer To House Vent"on page/4 of this manual. Flexible venting materials are knownto collapse, be easily crushed, and trap lint. These conditions willobstruct dryer airflow and increase the risk of fire.• Do not install or store this appliance in any location where itcould be exposed to water and or weather.• Save these instructions. (Installers: Be sure to leave theseinstructions with the customer).DETERMINE ELECTRICAL REQUIREMENTS FOR YOUR DRYER MODEL• This dryer must be connected to an individual branch circuit of proper voltage and frequency as specified on Rating Plate (located insidedryer door) with no other appliances or fixtures attached.EXCEPTION:• A 120V receptacle is located on the back on the dryer and is available only for use with a washer that is affixed to the dryer with aWDF-85 kit. It may not be used for any other appliance or any conditions other than slated above (208V & 240V models only).• Branchcircuit must be protected bythe requiredtime-delay fuses or circuit breakers208Vor 240Vinstallation- 30 amps 120Vinstallation15 or 20 amps.• The electrical installation must conform to the national and local codes.208V AND 240V MODELS ARE NOT APPROVED FOR 120V INSTALLATION.TOOLS YOU WILL NEEDSLIPJOINTPLIERSFLATBLADEANDPHILLIPSSCREWDRIVERSSTACKING KITS FOR DRYERS(Comeswith individuol Instollotion Instructions)[] Over wosher- Use Woll Mount Kit WHK-35 or- Stock Rock DSDR24 or- Stock Rock DSR-24[] For olcove ond closet depth ond widthrequirements see specific kit instructions[]All stocking kits ore ovoiloble from sourIocol soles outlet.MATERIALS YOU WILL NEED4"DIA.METALDUCT(RECOMMENDED)4"DUCTCLAMPS(2)4"DIA.FLEXIBLEMETAL(SEMI-RIGID) ORULLISTEDTRANSITIONDUCT(IFNEEDED)4"SPRINGKITWXO8X10077(INCLUDES2ELBOWS)CLAMPS12)4"DIA.FLEXIBLEMETAL(FOILTYPE)ULLISTEDTRANSITIONDUCT(IFNEEDED.)EXHAUSTHOOD%4"DIA.METALELBOWGLOVES%SAFETYGLASSES3/4"STRAINRELIEFULRECOGNIZEDDUCTTAPE)RYERPOWERCORDKIT(NOTPROVIDEDULRATED WITHDRYER)120/240V,]OAWITH3OR4PRONGS.IDENTIFYTHEPLUGTYPEASPERTHEHOUSERECEPTACLEBEFOREPURCHASINGLINECORD.UNPACKING AND PREPARING FOR INSTALLATION[] Prepare the area and exhaust for installation of new dryer.[]Check and ensure the existing external exhaust is clean and meets attached installation specifications.[] Remove the literature and accessories bag from the dryer drum. Place the literature in a convenient place.[] Using foam pads from dryer carton, turn dryer upside down as shown.[] Install knobs. For location, refer to the Owner's Hanual.[] Dryer is now ready to be mounted above washer using accessory kit.[] Remove the foam shipping pads from under dryer.[] Move the dryer to the desired location.[] Follow the steps in the following pages to connect the dryer to the external exhaust and power supply.PrintedinMexico 234D1588PO02 31-16687 01- 12 GE

/ 4

Related manuals for GE DSKP333EC2WW