GE JCS830 Manual

Also see for JCS830: Manual Owner's manual

GE JCS830 Manual Manual pdf 1 page image

MODEL JCS830SH. 1 of 6 295D1749G019 Pub. Num. 29-6199TO REMOVE COOKTOP• Turn the power off.• Slide the unit out.• Remove four (4) 1/4” hex head screws on the back of the unit securing therear trim.• Remove two (2) 1/4” hex head screws on the gap cover on the back of therange. (Single Oven Only)• Remove three (3) 1/4” hex head screws on the back of the unit securing thevent trim.• Rotate the vent trim forward and lift to disengage tabs to remove.• Remove four (4) 1/4” hex head screws on the back of the unit securing thecooktop.• Remove two (2) T-15 torx screws from the front sides of the range.•• Lift up cooktop and remove.Remove two (2) housing harness wire.CAUTION Raising the cooktop too high can break the glass.HOW TO REMOVE OR REPLACE THE DOORDISCONNECT POWER BEFORE SERVICINGIMPORTANT: Reconnect all grounding devices. All parts of this appli-ance capable of conducting electrical current are grounded. If groundingwires, screws, straps, clips, nuts or washers used to complete a path toground are removed for service, they must be returned to their originalposition and properly fastened.GROUNDING SPECIFICATIONSGround Path Resistance 0.10Ω Max.Insulation Resistance 250KΩ Min.INSTALLATION REQUIREMENTSPower Supply: This appliance must be supplied with proper voltage andfrequency, and connected to an individual properly grounded branch circuit,protected by a circuit breaker or time delay fuse, as noted on rating plate.Wiring must conform to the National Electrical Codes. The rating plate islocated on lower front frame behind the storage drawer.Overcurrent Protection RangesNEC RATING MAXIMUM KILOWATT RATING208V 236V 240V35 Amp – 12.4 12.440 Amp 12.4 15.4 16.050 Amp 17.4 21.4 22.00WARNING Electrical Shock HazardDeath or serious injury can result from failure to follow these instructions.•• Disconnect power before servicing this product.• Reconnect all grounding devices after service.• Replace all parts and panels before operating.TO REMOVE THE CONTROL PANELThe control panel contains the control, Left and Right Wing Boards1. Disconnect the power.2. First remove the cooktop (see remove cooktop).3. Remove the two (2) screws behind the manifold panel that attach it tothe side panel bracket.4. Pull the control panel straight out.CAUTION Place a protective covering (such as a towel) between theCAUTION Components are electrically HOT on control when voltagecontrol panel and the cooking surface to avoid damage to the control panel.is connected to oven. The Electronic Oven Control system consists of the control,key panel, oven sensor, door and lock assembly.NOTE: temperature/Mode Selection necessary for operation of Relay contacts.VOLTAGE MUST BE PRESENT ACROSS TERMINALS L1 TO N FOR CONTROLTO OPERATE.30" RADIANT SLIDE-IN CONVECTION SINGLEOVEN RANGEJCS830 RADIANT SINGLE OVENPrinted in MexicoRADIANT HEATING ELEMENT SYSTEMSHeating Elements: The radiant heating element consists of a spiral-woundresistance wire attached to microporous insulation with molded ceramic fiberwalls in a corrosion protected metal tray.The Heating Elements come in various sizes:• 6” - 240 Volt, 1200 Watts• 6” - 240 Volt, 1500 Watts• 6”/9” - 240 Volts, 3000 Watts• 12”/9” - 240 Volt, 3000 WattsIndentationSlotHingelockPull hinge locks down to unlock.To remove the door:1. Fully open the door.2. Pull the hinge locks down toward the doorframe, to the unlocked position. A tool, suchas a small flat-blade screwdriver, may berequired.3. Firmly grasp both sides of the door at thetop.4. Close door to the door removal position,which is halfway between the broil stopposition and fully closed.5. Lift door up and out until the hinge arm isclear of the slot.Removal positionTo replace the door:1. Firmly grasp both sides of the door at the top.2. With the door at the same angle as theremoval position, seat the indentation of thehinge arm into the bottom edge of the hingeslot. The notch in the hinge arm must befully seated into the bottom of the slot.3. Fully open the door. If the door will not fullyopen, the indentation is not seated correctlyin the bottom edge of the slot.4. Push the hinge locks up against the frontframe of the oven cavity to the lockedposition.5. Close the oven door.Hinge armBottomedge ofslotHingelockHingearmPush hinge locks up to lock.ELECTRONIC OVEN CONTROLCONTROL VOLTAGETerminals VoltageJ203-1 to J203-2 Wing Board120 VAC all the timeJ203-3 to J203-2 Wing BoardBroil COM (Pin 1) to QTH NO (pin 2)L1 to NL2 to NL1 to BAKE 240 VAC when cooking mode is activeand oven is not calling for heatL1 to BROILL1 to CONVECTJ902-1 to N 120 VAC when fan is turning CCWJ902-2 to N 120 VAC when fan is turning CCW*J903-1 to N 120 VAC when light is onJ901 to N 120 VAC when warming drawer is onJ903-2 to N 120 VAC locking or unlocking*Oven light not working. Make the following checks:• Check oven light bulb.• Light is to come on when door is opened-check voltage across light socket.Terminals should read 120VAC. If 0 volts, check jamb switch and wiring.• Light is to come on when control light pad is pressed. K906 should click. Checkvoltage from J903-1 to N. Should read 120VAC. If 0 volts, replace control.OVEN SENSOR AND DOOR SWITCH OHMMETER TESTRemove power from the oven. Make a resistance measurement from the sideof the sensor and lock switch connector with the exposed terminals unpluggedfrom the ERC.CIRCUIT TERMINALS OHMSOvenSensor4 to 5Unlatch 1 to 2 OpenLatch 1 to 2* If abnormal reading is observed, wiggleleads at connector at rear of cavity bet-ween broil elements pins. If any variation,replace sensor.