GE JS630SFSS Dimensions And Installation Information

GE JS630SFSS Dimensions And Installation Information Manual pdf 1 page image

JS630SFGE® 30" Slide-In Electric RangeDimensions and Installation Information (in inches)Listed byUnderwritersLaboratoriesFor answers to your Monogram® or GE®appliance questions, visit our website atgeappliances.com or call GE Answer Center®service, 800.626.2000.All GE ranges are equipped withan Anti-Tip device. The installationof this device is an important,required step in the installationof the range.320632Specification Created 6/13AcceptableElectricalOutlet Area30" Min.30" Min.Shave Raised Edge To Clear31-1/8" Wide Control PanelExcluding Model JSS282-7/8"To FrontSurface OfCountertop20-5/8" DoorClearanceFrom FrontSurface ofCountertop31-1/43025-3/4*Recommended6" Min.From Walls23-3/1615" Min.2-1/230259/167-1/22-1/224(excluding handle35-7/8"–38"from floor tocountertopIf the countertop area is not flat, excess tension may be applied to the glass cvoiding the warranty. Make sure the wall covering, countertop, flooring andwithstand the heat (up to 200°F) generated by the range.A. Allow 30" minimum clearance between surface units and bottom of unprallow a 24" minimum when bottom of wood or metal cabinet is protecteflame-retardant millboard covered with no less than No. 28 MSG sheet msteel, .025" aluminum or .020" copper.B. This appliance has been approved for 0" spacing to adjacent surfaces aboHowever, a minimum 6" spacing to surfaces less than 15" above the cookis recommended to reduce exposure to steam, grease splatter and heat.clearance at the back wall.To reduce the risk of burns or fire when reaching over hot surface elements,cooktop should be avoided. If cabinet storage space is to be provided aboveby installing a range hood that projects at least 5" beyond the front of the caAcceptableElectricalOutlet Area30" Min.30" Min.Shave Raised Edge To Clear31-1/8" Wide Control PanelExcluding Model JSS282-7/8"To FrontSurface OfCountertop20-5/8" DoorClearanceFrom FrontSurface ofCountertop31-1/43025-3/4*Recommended6" Min.From Walls23-3/1615" Min.42-1/230259/167-1/22-1/2AccessoryBackguard JXS322436-1/4(excluding handle) *Total depth from wall tofront of closed oven doorincluding handle is 28-1/2.35-7/8"–38"from floor tocountertopIf the countertop area is not flat, excess tension may be applied to the glass cooktop, causing breakage andvoiding the warranty. Make sure the wall covering, countertop, flooring and cabinets around the range canwithstand the heat (up to 200°F) generated by the range.A. Allow 30" minimum clearance between surface units and bottom of unprotected wood or metal cabinet, orallow a 24" minimum when bottom of wood or metal cabinet is protected by no less than 1/4"-thickflame-retardant millboard covered with no less than No. 28 MSG sheet metal (.015" thick), .015"-thick stainlesssteel, .025" aluminum or .020" copper.B. This appliance has been approved for 0" spacing to adjacent surfaces above the cooktop.However, a minimum 6" spacing to surfaces less than 15" above the cooktop and adjacent cabinetryis recommended to reduce exposure to steam, grease splatter and heat. Allow 1/4" minimumclearance at the back wall.To reduce the risk of burns or fire when reaching over hot surface elements, cabinet storage space above thecooktop should be avoided. If cabinet storage space is to be provided above the cooktop, the risk can be reducedby installing a range hood that projects at least 5" beyond the front of the cabinets.23-3/163030If you are NOT using theFiller strip or Backguard:If you are using theFiller strip or Backguard:25ADA qualified basedon Uniform FederalAccessibility Standards*Receptacle Locations: Locally approved flexible service cord or conduit mustbe used because terminals are not accessible after range installation. Seeshaded area in drawing for location of electrical outlet box. Recommendedoutlet locations allow range to be installed directly against rear wall.Note: This appliance has been approved for 0” spacing to adjacentsurfaces above the cooktop. However, a 6” minimum spacing to surfacesless than 15” above the cooktop and adjacent cabinet is recommendedto reduce exposure to steam, grease splatter and heat.Installation Information: Before installing, consult installation insgtructionsfor current dimensional data and additional requirementsOptional Kits For Slide-InElectric Ranges(Available At Additional Cost)Accessory Backguards(Attaches to the back of rangeas a backguard when unit isinstalled in 30" free-standingcutout)JXS32SS (Stainless) - 4" HighJXS32BB (Black) - 4" HighBody Sides(Slide-in ranges are soldwithout sides installed. Canbe installed on either leftor right when unit has oneexposed side [no cabinetadjacent]. Kit contains1 body side)JXS77BB (Black)Rear Filler StripWB07T10680 - Black Filler Strip AssemblyOptional Lower Trim Kits(If counter height is greaterthan 36.5", a lower trim kitis recommended to extendthe useful height to 38"maximum)JXS56BB – BlackEdge To ClearControl Paneldel JSS28oor31-1/43015" Min.425/2AccessoryBackguard JXS3236-1/423-3/163030If you are NOT using theFiller strip or Backguard:If you are using theFiller strip or Backguard:25AcceptableElectricalOutlet Area30" Min.30" Min.Shave Raised Edge To Clear31-1/8" Wide Control PanelExcluding Model JSS282-7/8"o Frontrface Ofuntertop20-5/8" DoorClearanceFrom FrontSurface ofCountertop31-1/43025-3/4*3/1615" Min.4-1/230259/167-1/22-1/2AccessoryBackguard JXS322436-1/4(excluding handle) *Total depth from wall tofront of closed oven doorincluding handle is 28-1/2.23-3/163030If you are NOT using theFiller strip or Backguard:If you are using theFiller strip or Backguard:25KW Rating240V 11.9208V 8.9Breaker Size240V 40 Amps †208V 40 Amps ††Note: Check local codes for required breaker size.

/ 2

Related manuals for GE JS630SF