GE Profile PS905SPSS Dimensions And Installation Information

For answers to your Monogram,® GE Profile™ orGE® appliance questions, visit our website atge.com or call GE Answer Center® service,800.626.2000.PS905SPGE Profile™ 30" Slide-In Electric RangeSpecification Created 5/09 220443All GE ranges are equipped withan Anti-Tip device. The installationof this device is an important,required step in the installationof the range.Listed byUnderwritersLaboratoriesDimensions and Installation Information (in inches)28-1/4*36Maintainat least 6"from nearestcombustiblesurface.AcceptableElectricalOutlet Area30" Slide-In RangeDimensions (in inches)45-1/82-1/4564-1/23030" Min.15" Min. 630" Slide-in Elec. RangeAug. 8, 2003 -km23-3/163030If you are NOT using theFiller strip or Backguard:If you are using theFiller strip or Backguard:25*Wall to front ofclosed door handleon model JSP34.28" on modelsJSP26/JSS26/16.Note: Range may be placed with 0" clearance (flush) at the back wall and side wallsbelow countertop if the range side trims above the countertop extend beyond the cabinetfronts at least 1/4". (Self-clean models only.) Maintain at least 6" distance from nearestcombustible surface.3031-1/228-1/4*36Maintainat least 6"from nearestcombustiblesurface.AcceptableElectricalOutlet Area30" Slide-In RangeDimensions (in inches)45-1/82-1/4564-1/23030" Min.15" Min. 630" Slide-in Elec. RangeAug. 8, 2003 -km23-3/163030If you are NOT using theFiller strip or Backguard:If you are using theFiller strip or Backguard:25*Wall to front ofclosed door handleon model JSP34.28" on modelsJSP26/JSS26/16.Note: Range may be placed with 0" clearance (flush) at the back wall and side wallsbelow countertop if the range side trims above the countertop extend beyond the cabinetfronts at least 1/4". (Self-clean models only.) Maintain at least 6" distance from nearestcombustible surface.3031-1/2Note: Cabinets installed adjacent to slide-in ranges must have an adhesionspec of at least 194° temperature rating.Note: To reduce the possibility of scorching the side walls above the countertopwhen no load is present on burners, it is recommended that a minimum 6"spacing from adjacent side wall be allowed for possible extended high-heat ele-ment operation.Receptacle Locations: For all 30" Slide-In Ranges locally approved flexibleservice cord or conduit must be used because terminals are not accessibleafter range installation. See shaded area in drawing for location of electricaloutlet box. Recommended outlet locations allow range to be installed directly against rear wall.KW Rating240V 11.6208V 8.7Breaker Size240V 40 Amps208V 40 AmpsInstallation information: Before installing, consult installation instructionspacked with product for current dimensional data.Optional Kits For Slide-InElectric Ranges(Available At Additional Cost)Accessory Backguards(Attaches to the back of rangeas a backguard when unit isinstalled in 30" free-standingcutout)JXS32SS (Stainless) - 4" HighJXS32WW (White) - 4" HighJXS32BB (Black) - 4" HighJXS37WW (White) - 5-1/4" HighJXS37CC (Bisque) - 5-1/4" HighJXS37BB (Black) - 5-1/4" HighBody Sides(Slide-in ranges are soldwithout sides installed. Canbe installed on either leftor right when unit has oneexposed side [no cabinetadjacent]. Kit contains1 body side)JXS77WW (White)JXS77BB (Black)Rear Filler StripWB07T10680 - Black Filler Strip AssemblyOptional Lower Trim Kits(If counter height is greaterthan 36.5", a lower trim kitis recommended to extendthe useful height to 38"maximum)JXS56WW – WhiteJXS56BB – BlackAcceptableElectricalOutlet Area30" Min.30" Min.Shave Raised Edge To Clear31-1/8" Wide Control PanelExcluding Models JSS28 and JSP392-7/8"To FrontSurface OfCountertop20-5/8" DoorClearanceFrom FrontSurface ofCountertop31-1/43025-3/4**Recommended6" Min.From Walls23-3/1615" Min.A/B*13" Max.2-1/230259/167-1/22-1/2AccessoryBackguard2436-1/4*JXS37 is 5-1/4" an(excluding handle) **Total depth from wfront of closed oveincluding handle i35-7/8"–38"from floor tocountertopAcceptableElectricalOutlet Area30" Min.30" Min.Shave Raised Edge To Clear31-1/8" Wide Control PanelExcluding Models JSS28 and JSP392-7/8"To FrontSurface OfCountertop20-5/8" DoorClearanceFrom FrontSurface ofCountertop31-1/43025-3/4**Recommended6" Min.From Walls23-3/1615" Min.A/B*13" Max.2-1/230259/167-1/22-1/2AccessoryBackguard2436-1/4*JXS37 is 5-1/4" and JX(excluding handle) **Total depth from wall tfront of closed oven dincluding handle is 2735-7/8"–38"from floor tocountertopIf the countertop area is not flat, excess tension may be applied to the glass cooktop causing breakageand voiding the warranty. Make sure the wall covering, countertop, flooring and cabinets around the rangecan withstand the heat (up to 200˚F) generated by the range.A. Allow 30" minimum clearance between surface units and bottom of unprotected wood or metal cabinet,or allow a 24 " minimum when bottom of wood or metal cabinet is protected by no less then 1/4 " thickflame retardant millboard covered with no less than No. 28 MSG sheet metal (.015 " thick), .015 " thickstainless steel, .025 " aluminum or .020 " copper.B. This appliance has been approved for 0 " spacing to adjacent surfaces above the cooktop. However,a minimum 6 " spacing to surfaces less than 15 " above the cooktop and adjacent cabinetryis recommended to reduce exposure to steam, grease splatter and heat. Allow 1/4 " minimum clearanceat the back wall.To reduce the risk of burns or fire when reaching over hot surface elements, cabinet storage space abovethe cooktop should be avoided. If cabinet storage space is to be provided above the cooktop, the risk canbe reduced by installing a range hood that projects at least 5 " beyond the front of the cabinets. Cabinetsinstalled above the cooktop must be no deeper than 13 ".

/ 2

Related manuals for GE Profile PS905SP