Genie GCL-T Specifications

Also see for GCL-H: Product guide

Genie GCL-T Specifications Manual pdf 1 page image

www.GenieCompany.com/commercial | 800.843.4084Model GCL - T / J / HStandard-Duty SpecificationsPART 1 – GENERAL1.01 WORK INCLUDEDA. Provide electric door operator(s) of size and capacity recommended for door(s)as provided by door manufacturer with electric motor and factory pre-wiredmotor controls, starter, reduction unit, disc brake (option for no brake on 1/2HP), clutch, control devices, and accessories required for proper operation.1.02 RELATED WORKA. Opening preparation, miscellaneous or structural metal work, access, fieldelectrical wiring, wire conduit, fuses and disconnect switches are in theScope of Work of other divisions or trades.1.03 QUALITY ASSURANCEA. In accordance with accepted quality assurance guidelines for motor-operateddoors, both the door and electric operator shall be manufactured by a single-source producer of door systems.PART 2 - PRODUCT2.01 GENERALA. The electric door operator shall be the Model GCL Standard-Duty door controlsystem for a (standard lift) (lift-clearance), (full-vertical) sectional door and /or (rolling steel door) and /or (rolling steel grille) as manufactured by TheGenie Company and suitable for the type and size of door specified.B. The electric operator shall be (single phase) (three phase) with MultiVolt™ -the ability to adjust to the correct voltage of (115/208/230 for single phase)(208/230/460 for three phase) without removal or addition of any parts. (Theelectric operator shall be 575VAC three phase).C. All components to have corrosion resistant coatings.D. The operator shall be suited for NEMA ICS 6 Type 1 (NEMA ICS 6 Type 4)(NEMA ICS 6 Type 4X) environment.2.02 MOTORA. Motor shall be:a. (1/2 horsepower single phase or three phase with automatic thermalreset overload)b. (3/4 horsepower or 1 horsepower single phase with manual resetoverload)c. (3/4 horsepower or 1 horsepower three phase with automatic thermalreset overload)Motor frame shall comply with NEMA (48 for ½ HP single phase) (56 for½ HP three phase, ¾ & 1 HP all phases), (open drip-proof construction)(Totally Enclosed Non Ventilated – TENV construction) (Totally Enclosed FanCooled – TEFC construction).2.03 REDUCTIONA. Primary reduction is TensiBelt™, an auto-tensioning poly-V flex belt that doesnot require adjustment. Secondary reduction is by chain and sprocket.2.04 DUTY CYCLEA. Duty cycle shall accommodate standard usage, up to 30 cycles per hour, notto exceed 100 cycles per day.2.05 BRAKEA. Brake shall be a DC Disc type with selectable Progressive Braking forsmooth stopping.2.06 CLUTCHA. Clutch shall be adjustable friction disc type standard on all versions.2.07 LIMIT SYSTEMA. The EZ Limit™ system shall be magnetic type providing absolute positioningwith push to set capabilities. The Limit System shall remain synchronizedwith the door during manual operation and supply power interruptions.2.08 CONTROL SYSTEMA. The control system shall be microprocessor-based with relay motor controlson a single board. This system will incorporate a 16-character liquid crystaldisplay (LCD) to display the system status. This system shall be capableof monitoring and reporting on a variety of operating conditions, including:current operating status, current command status, motor movement status,current error status (if applicable), hoist Interlock status (if applicable),external Interlock status, and 24VDC status.B. The control system shall feature a delay-on-reverse operating protocol.C. The system shall include maximum run timers in both directions of travel thatlimit motor run time in the event a clutch slips or some other problem occurs.D. It shall include provisions for the connection of a 2-wire monitored photocellsystem or a 2-wire monitored edge sensor, as well as non-monitored 2-wiresensing edges, photocells or other entrapment protection devices.E. Control action will be constant contact close until a monitored entrapmentdevice is installed, allowing for selection of momentary contact.F. The system shall include provisions for connection of single and/or 3-buttoncontrol stations.G. The system shall include provisions for connection of an external 3-wireradio control and related control devices.H. The control system shall include on board open, close and stop control keysfor local operation.I. Trolley operators shall include an inherent, secondary reversal system.J. The control system will include an IntelliCode® I radio receiver that is315Mhz and capable of storing 50 single button and/or 50 open-close-stoptransmitters with the ability to add and/or delete transmitters individually,identify and store activating transmitter ID(s).2.09 MOUNTINGA. Mounting for sectional doors shall be side (center) by chain/sprocket on(jackshaft) (hoist) models.B. Mounting for sectional doors via drawbar coupling for (trolley)(side-mounttrolley) (dual trolley).C. Mounting for rolling steel doors shall be (front of hood) (wall-mount)and chain/sprocket coupling to door.D. Mounting for hoist models shall be ordered from factory (left hand) (righthand).2.10 RELEASEA. (Release shall be a pull and hold type mechanism with single cable operationand an integrated interlock switch on hoist units.) (Release shall consist of amanual disconnect door arm on trolley units).2.11 HOISTA. Chain hoist shall consist of chain pocket wheel, chain guard and smoothhand chain on hoist units. Standard on hoist models (optional on trolley asside mount kit).2.12 SECONDARY REVERSALA Trolley version only shall include an integral electronic reversing system thatwill stop and reverse a closing door upon detection of an obstruction anddesigned to accept an optional external reversing device.B. (Jackshaft)(Hoist) models shall be designed to accept an optional externalreversing device.NOT FOR RESIDENTIAL USE.2.13 OPTIONAL CONTROL ACCESSORIESA. Control accessories: In (lieu of) (addition to) (interior push-button controlstation) (exterior push-button control station) (interior key switches) (exteriorkey switches) (radio control) (Genie monitored photo electric eyes)(commercial photo electric eyes) (floor loops) (motion sensors).B. Operator accessories shall be timer to close and will provide auxiliary controlinputs, auxiliary safety inputs, auxiliary timer hold input, and an automaticdoor closing feature with a user selectable time delay. Safety inputs are to beenabled or disabled using the on board keypad.C. Operator accessories shall be Auxiliary Output Module and will provideseveral auxiliary sets of dry contacts that are microprocessor controlled.Provides contacts for (up) (down) (mid-stop) limit. Provides contacts to beconfigured using the on board keypad to activate (lights)(horn)(strobes) whiledoor is running (up)(down)(both up and down).PART 3 - EXECUTION3.01 The Model GCL Standard Duty™ shall be installed in accordance with TheGenie Company instructions and standards. Installation will be by trainedand authorized Genie Company distributors or dealers.©2012 The Genie Company. All Rights Reserved.A copyright license to reproduce this specification is hereby granted to non-manufacturing architects, engineers and specification writers.Note to specifier:This specification is a suggested guide. Available options are shown in parentheses.

/ 2

Related manuals for Genie GCL-H