Genie Wireless Keypad Operating Instructions Manual

Also see for Wireless Keypad: Instructions Operationg instructions Instructions

Contents

operating instructions

Genie Wireless Keypad Operating Instructions Manual Manual pdf 1 page image

STEP 1: SETTING YOUR WIRELESS KEYPAD PIN(PERSONAL IDENTIFICATION NUMBER)A Activate programming mode.• Press (in order) .– Red LED blinks - once per second.• Enter your PIN (3 to 8 characters).• Press .– Red LED blinks - twice per second and turns off.STEP 1: SETTING YOUR WIRELESS KEYPAD PIN(PERSONAL IDENTIFICATION NUMBER)A Activate programming mode.• Press (in order) .– Red LED blinks - once per second.• Enter your PIN (3 to 8 characters).• Press .– Red LED blinks - twice per second and turns off.3DEF1 24 5 67 8 90GHI JKL MNOPQRS TUV WXYZ9VOF U.S. & IMPORTED PARTSThis Wireless Keypad is compatible with all INTELLICODE® radio equipped GENIE® products. • Drill with 1/16" Drill Bit• Phillips Screwdriver• Pencil• Mounting Screws INCLUDED insideBattery CompartmentInterchangeableFlip-up Coveravailable in 3optional ClassicColors to matchyour home’sexterior decorRed LEDindicatesBattery Powerand Statusduring Useand ProgrammingBacklit Keypadfor Ease of Useat NightBatteryCompartment9 Volt Battery(included)Instructions• Ability to Control up to threeGenie® INTELLICODE® Openers• Simple to Program and Install• PIN Codes can be up to 8 Characters• Low Battery Power Indicator• Stays Programmed DuringBattery Change• Temporary PIN for Special Purpose AccessOPERATING INSTRUCTIONS (KEEP FOR FUTURE REFERENCE)A Moving Door can cause serious injury or death.1 Keep people clear of opening while Door is moving.2 Do Not allow children to play with Wireless Keypad.3 During programming, the Door Opener could begin to run, so stay away fromthe moving Door and its parts. To keep the Door from moving, close the Doorand disconnect it from the Opener by pulling the Emergency Release Cord.3528135717WARNINGSTEP 3: OPERATING ONE DOOR OPENERA To move the Garage Door.• Enter your PIN.• Press .STEP 2: PROGRAMMING ONE DOOR OPENERA Find the Learn Code Button and Learn CodeIndicator LED on your door opener.– If your Door Opener has ablack Antenna Wire,the Learn Code Buttonand Indicator LEDare located near the Antenna.(The Light Lens may needto be opened.)– If your Door Opener does nothave an Antenna,you have an External Receiver.The External Receiver covermust be removed to accessthe Learn Code Buttonand Indicator LED.• Press the Learn Code Button.– Learn Code Indicator LED (on Opener) will blink.• Enter your PIN and press on Keypad.– Learn Code Indicator LED stays on.• Press again.– Learn Code Indicator LED turns off.• Press again.– Door moves.BASIC PROGRAMMING FORONE DOOR OPENERRed IndicatorLEDLearnCodeButtonLocatedon OpenerHousingSTEP 3: PROGRAMMING DOOR OPENERSA Decide which Door will be Door #1,#2 and #3.• Press the Learn Code Button (see Section 1 Step 2).– Learn Code Indicator LED (on Opener) blinks.• Enter your PIN and press on Keypad.– Learn Code Indicator LED stays on.• Press the number you have picked for thisDoor Opener ( or or ).– Learn Code Indicator LED stays on.• Press .– Learn Code Indicator LED turns off.B Repeat step A above for each Door Opener.Each Door Opener must be programmed to receive thesignal from the Wireless Keypad.STEP 4: OPERATING 2 OR 3 DOOR OPENERSA To move one of the Doors.• Enter your PIN.• Press .• Press Door Opener number ( or or ).SEE NOTE AT BOTTOM OF SECTION 1Proceed to Section 3 - Mounting Instructions.PROGRAMMING FOR2 OR 3 DOOR OPENERS MOUNTING INSTRUCTIONSThe Keypad must be mounted in sight of the Door(s), atleast 5 feet above the ground and clear of any movingDoor parts.A Mount Keypad.(Mounting screws located insideBattery Compartment.)• Remove Battery Cover (See Section 4 Figure 2).• Drill a 1/16”pilot hole for the top mounting screw.• Install a screw into the drilledhole,leaving a 1/8" gapbetween the screw headand the wall. See Figure 1.• Hook the Keypad overthe screw.• Mark,drill pilot hole andfasten bottom screw.• Reinstall Battery Cover.For answers to questions, call 1-800-35 GENIE, or visitwww.geniecompany.comAdditional Genie® products can be ordered using the Accessoriespage in your Owner’s Manual or through the 800 number above.FOR CONVENIENCEProgram Keypad BEFORE mounting.SECTION1 SECTION2 SECTION3ADDITIONAL OPERATIONSSECTION4USING A TEMPORARY PINA temporary PIN allows temporary access to your home byrepair persons, meter readers, etc.if you so desire.A Enter your PIN.• Press .B Enter the Temporary PIN (from 3 to 8 characters).• Press .NOTE• DO NOT reprogram the Door Opener(s).• Temporary PIN remains active until the next time yournormal PIN is entered.FORGOT YOUR PINORCHANGING YOUR PINA Erase old PIN.• Press and hold in order -.– Red LED will blink once and turn off.• Release all buttons.B Programming Door Opener(s).• Return to“Programming” (Section 1 or Section 2).Wallscrew head gapFigure 1FOR CONVENIENCEProgram Keypad BEFORE mounting.STEP 2: PROGRAMMING THE KEYPAD FORMULTIPLE DOOR OPENERSA All Door Openers will use the same PIN.• Enter your PIN and press .– Red LED blinks - once per second.• Press again.– Red LED blinks - twice per second.• Press the number of Doors (total) you wishto control ( or ).• Press .– Red LED blinks several times and turns off.ProgramButtonFEATURES :TOOLS NEEDED:If Safety Reverse does not work properly:1 Close Door and disconnect the Opener using Emergency Release Cord.2 Do not use Door Opener, Remote Controls, or Wireless Keypad.3 Refer to Door and Door Opener Owner’s Manuals before attempting any repairs.1"8Printed in the U.S.A.©2005 The Genie Company, D.B.A. GMI Holdings, Inc.FCC and IC CERTIFIEDThis device complies with FCC Part 15 and RSS 210 of Industry Canada. This equipment has been tested andfound to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection against harmful interference in a residential installation. Thisequipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordancewith the instructions, may cause harmful interference to radio communications. However, there is no guaranteethat interference will not occur in a particular installation. If this equipment does cause harmful interference toradio or television reception, which can be determined by turning the equipment off and on, the user isencouraged to try to correct the interference by one or more of the following measures: 1. Re-orient orrelocate the receiver antenna. 2. Increase the separation between the opener and receiver. 3. Connect theopener into an outlet on a circuit different from that to which the appliance is connected. 4. Consult the dealer.Changes or modifications not expressly approved by the manufacturer could void the user’s authority tooperate the equipment.CHANGING BATTERYIf the red LED doesnot blink during use,the battery needs tobe changed.1 2 34 5 67 8 90DEFGHI JKL MNOPQRS TUV WXYZPROGBatteryPress hereFigure 2BottomMountingScrewRed LEDCovers available in:• Brown - P/N 35365R• Almond - P/N 35365S• Sandstone - P/N 35365TProceed to Section 3 - Mounting Instructions.NOTE• If the Door does not move,check the red LED onKeypad. If the LED is blinking rapidly,the PIN wasentered incorrectly. After the LED stops blinking,re-enter your PIN and try again.• Any Keypad Button will control the Door for 30 secondsafter the Door starts moving.• Rapid blinking of the red LED indicates an error. After afew seconds the LED will turn off. Start over.Wait until Keypad Backlight turns off (approximately 30 seconds).Wait until Keypad Backlight turns off (approximately 30 seconds).

/ 1

Related manuals for Genie Wireless Keypad