H3C S5500-SI Series Ethernet SwitchesHigh AvailabilityConfiguration GuideHangzhou H3C Technologies Co., Ltd.http://www.h3c.comDocument Version: 20100722-C-1.03Product Version: Release 2202

H3C S5500-SI Series Configuration Manual

dhcp configuration examples

Chapter 1 DHCP Functions Overview

Configuration Guide

Configuring the DHCP Relay Agent

Configuring DHCP Snooping

Chapter 2 Configuration Examples

Network Diagram

DHCP Relay Agent/Snooping Configuration Examples

Configuration Procedure

Precautions

Chapter 3 Related Documents

chapter 1 qacl overview

network environment

time-based acl plus rate limiting plus traffic policing configuration example

configuration example of traffic measurement plus port redirection

configuration example of local traffic mirroring

other functions referencing acl rules

configuration example of web cache redirection

x configuration example

chapter 1 802.1x overview

chapter 2 802.1x configuration commands

authentication configuration example

configuring the switch

chapter 3 enterprise network access authentication configuration example

configuring the radius server

configuring the supplicant system

verifying configuration

ssh configuration example

introduction to ssh

ssh configuration

ssh configuration commands

configuration commands

configuring an h3c switch as an ssh client

chapter 3 ssh configuration example

when the switch acts as an ssh server and the authentication type is rsa

when the switch acts as an ssh client and the authentication type is password

when the switch acts as an ssh client and the authentication type is rsa

chapter 1 routing overview

configuration task list

rip configuration

ospf configuration

bgp configuration

route policy configuration

configuration examples

rip configuration examples

dr configuration example

ospf virtual link configuration examples

bgp confederation configuration example

bgp route reflector configuration example

bgp path selection configuration example

enable ospf

chapter 3 comprehensive configuration example

devices used for networking

software version

rip, static route, and routing policy configuration example

bgp and igp interaction configuration example

route backup configuration example

bgp med attribute configuration example

verifying the configuration

verifying the route backup configuration

verifying the med attribute configuration

chapter 1 multicast protocol overview

support of multicast features

configuring igmp snooping

configuring igmp

configuring pim

configuring msdp

pim-sm plus igmp plus igmp snooping configuration examples

igmp snooping-only configuration examples

msdp configuration examples

vlan configuration examples

configuring basic vlan settings

configuring basic settings of a vlan interface

protocol vlan configuration

vlan configuration example

voice vlan configuration examples

configuring voice vlan

qinq configuration examples

chapter 1 qinq overview

configuring qinq

configuring selective qinq

qinq configuration example

reserved protocol type values

chapter 1 arp attack prevention overview

arp attack prevention

ip static binding

S5500-SI Series

Chapter 1 SSL Configuration

SSL Configuration Task List

SSL Server Policy Configuration Example

Configuring an SSL Client Policy

Chapter 2 HTTPS Configuration

Associating the HTTPS Service with an SSL Server Policy

Associating the HTTPS Service with a Certificate Attribute Access Control Policy

Associating the HTTPS Service with an ACL

HTTPS Configuration Example

command conventions

obtaining documentation

documentation feedback

IP routing basics

load sharing

Static routing configuration

configuring a static route

configuring bfd for static routes

BFD echo packet mode

Displaying and maintaining static routes

Static route configuration examples

Static route FRR configuration example

BFD for static routes configuration example (direct session)

BFD for static routes configuration example (indirect session)

RIP overview

Operation of RIP

RIP message format

Supported RIP features

Protocols and standards

Configuring RIP basic functions

Configuring RIP route control

Disabling host route reception

Advertising a default route

Configuring a priority for RIP

Tuning and optimizing RIP networks

Configuring the maximum number of load balanced routes

Enabling source IP address check on incoming RIP updates

Specifying a RIP neighbor

Configuring RIP FRR

Configuring BFD for RIP

Displaying and maintaining RIP

Configuring RIP route redistribution

Configuring an additional metric for a RIP interface

Configuring RIP to advertise a summary route

RIP FRR configuration example

Configuring BFD for RIP (single-hop detection in BFD echo packet mode)

Configuring BFD for RIP (bidirectional detection in BFD control packet mode)

configure static routes

Troubleshooting RIP

Introduction to OSPF

Area based OSPF network partition

Router types

Classification of OSPF networks

dr and bdr

OSPF packet formats

Supported features

Enabling OSPF

Configuration procedure

Configuring OSPF areas

Configuring an NSSA area

Configuring OSPF network types

Configuring the OSPF network type for an interface as broadcast

Configuring the OSPF network type for an interface as P2MP

Configuring OSPF route control

Configuring OSPF inbound route filtering

Configuring ABR Type-3 LSA filtering

Configuring the maximum number of OSPF routes

Configuring OSPF route redistribution

Advertising a host route

Configuration prerequisites

Specifying LSA transmission delay

Specifying the LSA generation interval

Configuring stub routers

Adding the interface MTU into DD packets

Logging neighbor state changes

Enabling message logging

Configuring the LSU transmit rate

Configuring OSPF Graceful Restart

Configuring the OSPF GR Helper

Triggering OSPF Graceful Restart

Displaying and maintaining OSPF

ospf configuration examples

configuring ospf to advertise a summary route

configuring an ospf stub area

configuring an ospf nssa area

configuring ospf dr election

configuring ospf virtual links

configuring route filtering

configuring ospf frr

configuring bfd for ospf

troubleshooting ospf configuration

IS-IS configuration

configuring the is level and circuit level

configuring the network type of an interface as p2p

configuring the maximum number of equal cost routes

configuring a dis priority for an interface

enabling an interface to send small hello packets

configuring spf parameters

configuring system id to host name mappings

enabling the logging of neighbor state changes

configuring area authentication

dis election configuration

bgp path attributes

bgp route selection

ibgp and igp synchronization

technical support

Multicast overview

Multicast features

Common notations in multicast

Multicast models

Multicast architecture