HANYOUNG NUX PSC Series Instruction Manual
  |
As for PSC Case, connect on thecontrol board case by 3~5.5MMelectric wire. For the 0 V terminal,connect on the control board casewith identical type of electricalwire and earth it.Perform as indicated above,and earth the PSC.Distance fromcontrol boxBelowAboveWiring of PSC1. If intense vibration or impact is applied on the transmitter for lengthmeasurement, the wrong pulse is generated causing malfunction, therefore,absolute care is necessary when selecting the installation and dispositionlocation.2. As much as the amount of pulse per cycle, the slit gap of rotation slit isnarrower, therefore can be easily affected by vibration, and the vibrationapplied during slow rotation or when stationary, may get transmitted to theshaft or the main body, causing wrong pulse generation, therefore, please takecaution. The vibration applied to the transmitter for length measurement canbecome a cause for wrong pulse generation, so please take caution in termsof installation location or location for attachment.An internal pressure of 500V DC exists between the Case and the electriccircuit, however, there are dangers of damage the electrical circuit if voltageis applied accidentally, so do not perform mega tests.On Mega Test1. During installation, do not apply impact on or twist the shaft of the transmitterfor length measurement.2. During installation, do not apply excessive force when combining the shaft oftransmitter for length measurement and the instrument.3. During installation, take caution because the life span of the transmitter forlength measurement is dependent on the usage condition and theenvironment.4. Do not decompose, modify, revise or repair this product. This may be acause of malfunction, electric shock or fire.5. Reassemble this product while the power is OFF. Otherwise, it may be acause of malfunction or electric shock.On InstallationAbout vibrationFor noise prevention1. Separate an input signal cable from an output signal cable. If separating is notpossible, please use the input signal cable after shielding it.2. If there is excessive noise from the power supply, using insulating transformerand noise filter is recommended.3. Do not connect anything to the unused terminals.4. After checking the polarity of terminal, connect wires at the correct position.5. As for wiring, ensure they are as short as possible.6. Having the same pipe for wiring of the transmitter for length measurementwith the power line or an identical connection could cause malfunction,therefore please take caution.7. Wrong connection of the wiring of transmitter for length measurement maydamage the internal circuit. Please take sufficient caution.About Wiring1.Before using the product you purchased, make sure that it is exactly what youordered.2. Make sure that there is no damage or abnormality of the product during thedelivery.3. The transmitter for measuring the length is composed of precision parts, socan easily be damaged with external impact, therefore handle with care.4. The shield wire of the transmitter for length measurement is not connected tothe case.5. When the product gets wet, the inspection is essential because there is dangerof an electric leakage or fire.6. For the continuous and safe use of this product, the periodical maintenance isrecommended.7. If you use the product with methods other than specified by the manufacturer,there may be bodily injuries or property damages.The caution on the safety stated above, must be kept, otherwise malfunctioncan be induced.Load Current : Max. 30 mARemaining voltage : Max.Load Current : Max. 10 mARemaining voltage : Min.Safety informationCAUTIONHEAD OFFICE1381-3, Juan-Dong, Nam-Gu Incheon, KoreaTEL: (82-32)876-4697 FAX : (82-32)876-4696MAIN PRODUCTS- DIGITAL : Temperature Controller, Counter, Timer,Speedmeter,Tachometer, Panel Meter, Recorder- SENSOR : Proximity Switch/Photo Electric Sensor,Rotary Encoder, Optical Fiber Sensor,Pressure Sensor- ANALOG : Timer, Temperature ControllerRotary EncoderPSCWe appreciate you for purchasing HanYoung NUX Co.,Ltdproduct. Before using the product you have purchased,check to make sure that it is exactly what you ordered. Then,please use it following the instructions below.INSTRUCTION MANUALMA0604E070130Specification |
Related manuals for HANYOUNG NUX PSC Series
manualsdatabase
Your AI-powered manual search engine