Haier ES15V-M1 User Manual
Also see for ES10V-M1: User manualUser manualService manualManual
ES35V-M1ES35V-M21 2ES10V-M1ES15V-M1ES25V-M1Spa Water HeaterUser's Manual0040502334VPlease read this manual before usage.Retain it for future reference.Safety warning (Read carefully before use) Pre-safe ExpertCheck if the ammeter and the diameterof the wires are in accordance withthe rated current of the water heater.If necessary, please have it checked byan experienced electrician.This water heater is available for AC230V/50Hz power.Be sure to use independent socketand earth it reliably, and socketquality shall conform to the nationalstandard requirements.Set the power socket of the waterheater at the dry position away fromspraying water. Do not plug/unplugwith wet hands.After installation, be sure to f ill theheater completely with water beforeswitching on the power in the f irstusage. Children must take a bathunder the supervision of adult.In opening and closing the watervalve, do not point the showerheadtoward the human body. Otherwiseit may hurt by the spraying hot water.During winter in a cold area, if the heateris idle for a long period, please pull thehandle of the safety valve to discharge thewater. Otherwise it may freeze inside thewater heater and cause damage.In case the power cord of the waterheater is damaged, be sure to have itreplaced by after service techniciansmanufacturer.Do not set at place that is too coldand may freeze.Do not set at outdoor places.Do not use as f loor standingappliances.Please mount it to f irm and reliablewall.Do not install to places withoutsewage.Connect the drain hose to the inletof the sewer to avoid polluting bysplashing.Never do that.Be sure to act as per instructions.The product adopts the patented "Safe Care" technology of our company. As long asproduct adopts civil power supply, even if the earthing wire is electrified by mistake, the"Safe Care" technology still can block dangerous electricity, and ensure your personalsafety. But if you f ind any perceptible current, please disconnect the power and contactafter service department for maintenance. Do not disassemble by yourself.The original pipeline of the water heater is an organic part of "Safe Care" . Do not removeit by yourself. Otherwise we will not take responsibility for injury and loss caused by thesafety danger occurring.This mark is the designation for Pre-safe Expert of Haier Water HeaterCompany, which indicates the use of the company's patented technologyinside the product. It ensures you a safe bath while monitoring whetheryour house ground wire is live or not all the time. If this mark is lit, itindicates your house ground wire was come live (poor grounding andlive). In this case, please immediately stop use and disconnect the power,and remember not to touch any electric appliance in your house. At thesame time, immediately contact after-sales service and your propertyPre-safe Expert will become the electric safeguard for your family.See to the physical for the appearance, color or pattem.Mark of Haier SafeWater HeaterElectric circuit diagramInstallation • UsageInstallation must be made by installers of, or designated by, our company after-servicedepartment. The water heater shall be wall-mounted.Make 2 holes Φ12mm, 65mm deep in wall with an impact drill according to the drawing ofthe external dimensions.Take out all accessories in packaging liner, unpack one hook, sleeve the ring end of theconnection lines among the accessories into the hook tightening end and assemble the hookwell. Afterwards, insert and fix two hooks into the holes (wherein the hook with connectionlines is fixed in the right hole). Lift the water heater and hang it with wall rack corresponding tothe two hooks. insert the connection spacer led from the rear shell wall rack of the heater intothe connection terminal of the line on the hook (See Figure 2). Install accessories such as safetyvalve as shown in Figure 3. Do use sealing compound to prevent water leakage.To facilitate installation and removal, it is suggested a G1/2 movable nut be fitted at appropriatelocations on inlet and outlet pipes respectively. Find the location requiring hot water supply.Connect inlet pipe, outlet pipe and city water pipe respectively to the use point for hot water.Note: The hot water pipe shall not be too long to reduce heat losses.Please reserve some space in installation for the future maintenance.InstallationLive wire (brown)High temperature limiterThermostatHeating indicatorHeating elementGrounding wire (yellow/green)Null line (blue)Packing listElectric waterheater (Set)Safety valveDrain hose(Unit)Expansionhook (PCS)User's manual(Copy)Connectingline (PCS)ES10V-M1ES10V-M2 1 1 2 1 11 1 2 1 11 1 2 1 11 1 2 1 1ES15V-M1ES15V-M2ES25V-M1ES25V-M2NameQuantityModelES35V-M1ES10V-M2ES15V-M2ES25V-M2ES35V-M2 |
Related manuals for Haier ES10V-M1
manualsdatabase
Your AI-powered manual search engine