Halco ProLED Vapor Tight Series Installation Manual
   |
ProLED ® Vapor Tight SeriesInstallation Guide ®© 2020 Halco Lighting Technologies, LLC. All rights reserved. Halco is a registered trademark of Halco Lighting Technologies. All sizes and specifications are subject to change.Halco Lighting Technologies | 2940 Pacific Drive | Norcross, GA 30071 | Toll Free 800.677.3334 | Phone 770.242.3612 | Fax 800.880.0822 | halcolighting.com | Atlanta | Chicago | Cleveland | Houston | Los Angeles | Phoenix`Vapor Tight Series Installa�on GuideSAFETY INSTRUCTIONS:Read instruc�ons carefully before a�emp�ng to install fixture.All wiring should be performed by a qualified electrician.Disconnect power before installing or servicing. This fixture must be wired in accordance with the Na�onal ElectricalCode and applicable local codes and ordinances.CAUTION: Risk of fileWARNING: Make certain power is OFF before installing or maintaining fixture. No user serviceable parts inside.WARNING: Do NOT handle energized fixture when hands are wet, when standing on wet or damp surfaces or inwater.WARNING: Fixture to be independently supported to building structure.CAUTION: Be sure the fixture temperature is cool enough to touch. Do NOT clean or maintain while the fixture is energized.1. Clean lens with non-abrasive cleaning solu�on.2. Do NOT open fixture to clean the LED. Do NOT touch the LED.Note: These instruc�ons do not cover all details or varia�on in equipment, nor do they provide for every possible situa�on duringinstalla�on, opera�on or maintenance.1. Check that the line voltage at fixture is correct. Refer to wiring direc�ons.2. Check that the fixture is grounded properly.Universal voltage driver permits opera�on at 120V through 277V, 50/60Hz.1. Connect the BLACK fixture lead to the (+) LINE supply lead.2. Connect the WHITE fixture lead to the (-) COMMON supply lead3. Connect the GROUND wire from fixture to the supply ground. Do NOT connect the GROUND of the dimming fixtureto the output.4. Connect the VIOLET fixture lead to the (V+) DIM lead.5. Connect the GRAY fixture lead to the (V-) DIM lead.CLEANING&MAINTENANCE:TROUBLESHOOTING:0-10V DIMMABLE WIRING:`Vapor Tight Series Installa�on GuideSAFETY INSTRUCTIONS:Read instruc�ons carefully before a�emp�ng to install fixture.All wiring should be performed by a qualified electrician.Disconnect power before installing or servicing. This fixture must be wired in accordance with the Na�onal ElectricalCode and applicable local codes and ordinances.CAUTION: Risk of fileWARNING: Make certain power is OFF before installing or maintaining fixture. No user serviceable parts inside.WARNING: Do NOT handle energized fixture when hands are wet, when standing on wet or damp surfaces or inwater.WARNING: Fixture to be independently supported to building structure.CAUTION: Be sure the fixture temperature is cool enough to touch. Do NOT clean or maintain while the fixture is energized.1. Clean lens with non-abrasive cleaning solu�on.2. Do NOT open fixture to clean the LED. Do NOT touch the LED.Note: These instruc�ons do not cover all details or varia�on in equipment, nor do they provide for every possible situa�on duringinstalla�on, opera�on or maintenance.1. Check that the line voltage at fixture is correct. Refer to wiring direc�ons.2. Check that the fixture is grounded properly.Universal voltage driver permits opera�on at 120V through 277V, 50/60Hz.1. Connect the BLACK fixture lead to the (+) LINE supply lead.2. Connect the WHITE fixture lead to the (-) COMMON supply lead3. Connect the GROUND wire from fixture to the supply ground. Do NOT connect the GROUND of the dimming fixtureto the output.4. Connect the VIOLET fixture lead to the (V+) DIM lead.5. Connect the GRAY fixture lead to the (V-) DIM lead.CLEANING&MAINTENANCE:TROUBLESHOOTING:0-10V DIMMABLE WIRING:●●●●● |
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine