Happymodel Mobula6 Quick Start Manual
M1M2M3M4+5VIR1RX1TX1BINDBOOTLED_STRIPTX2RX2Binding procedureFlight controller connection diagramToggle the AUX1 Switch, the Green LED onToggle the AUX1 Switch, the Green LED onthe Flight controller will getting to be solidthe Flight controller will getting to be solidToggle the AUX1 Switch, the Green LED onthe Flight controller will getting to be solidArm/Disarm the Motor1. The Default Arm/Disarm switch for is AUX1(Channel 5),and you can also customizeMobula6 HDit with Betaflight Configurator.3.The default channel map for Mobula6 HD DSM2/X version is TAER1234, please make sureyour transmitter is matched, otherwise it will can't be armed. Toggle the AUX1 Switch ,theGreen LED on the flight controller will getting to be solid, this indicates the motor was armed .And also you can found “Armed” displayed on your FPV Goggles or the FPV Monitor. Pleasemake sure keep the Mobula6 HD level before arming .Be careful and enjoy your flight now !Receiver configuration2.For most of Spektrum radio the default channel 5 is Gear switch and you can also customizeit. Use DX9 for example, Go to menu and select System setup ,then choose Channel ssign.BUZ-+5VGNDBAT+M1M2M3M4+5VIR1GNDRX1TX1BINDBOOTLED_STRIPTX2RX2Camera+5V outGND1. Betaflight 4.3.0 version(Original custom firmware out of box) binding procedure:Plugthe usb to power up for the Mobula6 HD, then press and hold the bind button for a second ,the red LED on the bottom of the flight controller will blinking fast , this indicate thereceiver is in bind mode2. Another simple way to bind with SPEKTRUM Radio or Multi protocol module withDSM2/DSMX protocol : Plug the usb to power up for the Mobula6 HD , then open Betaflightconfigurator and move to the CLI command , then type "bind_r x", the red Led on the bottomof the flight controller will blinking fast , this indicate the receiver is in bind mode .Makeyour radio transmitter get into bind mode . The red Led should getting to be solid orblinking slowly if bind successful .Please set Receiver mode to be SPI RX Support from the Configuration tab of the BetaflightConfigurator,then Select SPEKTRUM protocol for the SPI Bus Receiver provider, don't enableSerial RX since the CrazybeeX DXS Flight controller is integrated SPI BUS Receiver.Package includesFeaturesAIO 4IN1 Crazybee F4 Lite flight controller built-in 5.8G VTXExtreme light 1S 65mm Brushless HD whoop only 27gCome with Runcam Split3-lite 1080P HD DVRSmooth and agileCompatible for 1S Lipo/LIHVCamera Angle adjustableSpecificationsBrand Name: HappymodelItem Name: Mobula6 HD 1S 65mm Brushless whoop HD drone BNF versionWheelbase: 65mmSize: 80mm*80mm*40mmWeight: 27gReceiver option:Internal SPI Frsky version (Compatible with ACCST D8/D16, Recommend D8 mode)Internal SPI Flysky version(Compatible with AFHDS and AFHDS-2A Flysky transmitter)Internal SPI DSM2/DSMX version(Compatible with Spektrum DSM2/DSMX radio)External TBS CRSF NANO version(Compatible with TBS ransmitters)Qty114111411Item NameMobula6 HD 1S 65mm whoop Drone FrameSPI Receiver Option1: Crazybee F4 Lite FC built-in Frsky SPI D8 RXSPI Receiver Option2: Crazybee F4 Lite FC built-in Flysky SPI RXSPI Receiver Option3:CrazybeeX DXS V1.0 built-in DSM2/DSMX SPI RXExternal receiver option1:TBS CRSF NANO receiverEX0802 KV19000 brushless motorGemfan 1219-3 Propellers(4cw+4ccw)Runcam Split3-lite 1080P HD Camera +DVR5.8G 25mw 40ch vtx (Flight controller built-in)1S 250mah 30C LiHV Batter y1S Lipo/LIHV USB ChargerPropeller disassemble toolHappymodel Mobula6 HD 1S 65mm Brushless whoop DSM2/DSMX version |
Related manuals for Happymodel Mobula6
Happymodel Mobula7 Quick Start Manual
Happymodel Mobula7 Quick Start Manual
Happymodel Mobula6 1S Manual
Happymodel Mobula8 2S Manual
Happymodel Mobula7 User Manual
Happymodel Mobula7 HD PNP Manual
Happymodel Mobula7 HD DSMX Manual
Happymodel Mobula 7 1-2S Frsky Manual
Happymodel Crux35 Manual
Happymodel Larva X Manual
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine