JABSCO 37010-0097 Manual
Also see for 37010 Series: Quick start guideInstallationQuick start guideOperating instructionsQuick start guide
    |
ELECTRIC TOILET BASE KITFEATURES• High Capacity Macerator and Bowl Scavenger Pump• Flexible Impeller Flush Pump• Permanent Magnet Type Motor, Fully Enclosed,with Stainless Steel Shaft• Complies with USCG 183.410 and ISO 8846MARINE for Ignition Protection• Simple Push Button Switch included• All Corrosion Resistant Materials for Marine UseSPECIFICATIONS• 5/8" or 3/4" Inlet, 1" Outlet Back Flow Check Valvein Discharge• 1" x 1-1/2" Hose Adaptor included to adapt to 1-1/2"waste plumbing.• Thru Flow Approx. 1-1/2 Qts. per 5 Seconds ofOperationVARIATIONSMODEL NO. DESCRIPTION37010-0092* Toilet Conversion, 12 Volt EMC37010-0097* Toilet Conversion, 24 Volt EMC*This model is Marked and complies with EN50081-1 forsuppression of electro-magnetic interference.APPLICATIONThe Jabsco electric toilet may be installed above or belowthe waterline. Flush pump is self-priming with a vertical liftup to 4 feet; discharge macerator pump can operateagainst a vertical head up to 4 feet.The 37010 series can be used to convert the Raritan PHor Compact, Wilcox-Crittenden “Head Mate”, Groco HC,Brydon No. 9127, 9128, or No. 59128 and virtually anyother model marine toilet using the “standard” bowl config-uration with a 3-3/4" diameter bolt circle, 4 hole pattern inthe base. Check the dimensional drawing to be sure thebowl will fit the flange dimensions as shown.The 37010 series includes the complete motorized baseassembly, bowl gasket, four bolts and washers for bowl,two 5/8" to 3/4" pump port adaptors, 3/4" white hose, 1" to1-1/2" discharge port adaptor, and momentary controlswitch.ASSEMBLY1. Overall height after conversion may increase up to 1"on some models, check to be sure adequate space isavailable if located under seats or bunks.2. Screw 6mm machine screws with starlock washerunder each head into nuts positioned in the hex recesson the top of the base to form bowl attachment studs(see exploded view).3. Remove complete manual base assembly and mountbowl on Jabsco motorized base. NOTE: M6 x 50mmlong machine screws supplied are suitable for mostbowls; however some bowl flanges are heavier andlonger machine screws must be used. Place plasticwashers against bowl flange, positioning base formost convenient hose connection arrangement.4. Connect pump outlet to rear bowl connection with 3/4"hose. Install the hose clamp on the pump dischargeport only.5. Position complete toilet assembly and fasten securelyon flat surface. Be sure not to warp toilet base whentightening toilet base down.6. Connect existing inlet hose to pump inlet port. A 5/8" to3/4" sleeve adaptor is included for fitting to commonlyused 3/4" inlet hose size. Make sure all connectionsare airtight and free of sharp bends or restrictions.7. Connect 1" discharge hose to discharge port (1-1/2"hose when using 1-1/2" discharge adaptor) and makesuitable connection to holding tank or other dischargesystem. Avoid sharp bends or restrictions.8. For installation below the waterline, install a ventedloop in the intake hose and position about 8" above thewaterline at all angles of heel or trim. **A vented loopshould also be used for discharge if connected to athru-hull fitting.9. For installations above water line, make a loop in dis-charge line about 8 inches above base of bowl toretain water in bowl. Some installations may need aModel 37010-SeriesModel 37010-SeriesConversion Kitswww.PumpAgents.com - Click here for Pricing/Ordering for Pumps and PartsJabsco Pumps 37010-0097 |
Related manuals for JABSCO 37010 Series
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine